Instruction Sheet
408-8676
Production Torque Wrenches
27 OCT 14 Rev G
PROPER USE GUIDELINES
Cumulative Trauma Disorders can result from the prolonged use of manually powered hand tools. Hand tools are intended for occasional use and low
volume applications. A wide selection of powered application equipment for extended-use, production operations is available.
Open-End Torque Wrench
Protective Cover
Wrench Head
TE PREVIOUS WRENCH SIZE
CONNECTIVITY PART
WRENCH DESCRIPTION PRESET TORQUE
mm [inches]
PART NUMBER NUMBER
1055276-1 2098-0351-54 Production Torque Wrench 6.4 1/4 14 in-lbs 2 lb
1055419-1 2098-5065-54 For SMA (OSM) Type Connectors 7.9 5/16 8 in.-lbs +1.5/-.5 lb
1055480-1 2098-5304-54 For OSSM Type Connectors 6.4 1/4 5 in.-lbs .5 lb
1055512-1 2098-5619-54 For SMA (OSM) Hermetic Type Connectors 7.1 9/32 30 in.-lbs 2 lb
1055546-1 2098-5830-54 Production Torque Wrench Kit 6.4 and 8.0 1/4 and 5/16 8 in.-lbs +1.5/-.5 lb
1055790-1 2598-5026-54 For SC/N Type Connectors (Hex Nut Design) 20.6 13/16 14 in.-lbs 2 lb
1055791-1 2598-5027-54 For TNC Type Connectors (Hex Nut Design) 15.9 5/8 14 in.-lbs 2 lb
1055826-1 2598-5160-54 Production Torque Wrench 4.0 5/32 8 in.-lbs +1.5/-.5 lb
1055868-1 2598-5298-54 For TNC Type Connectors (Hex Nut Design) 14.3 9/16 14 in.-lbs2 lb
1061789-1 7098-5031-54 For 7mm Type Connectors 19.1 3/4 14 in.-lbs 2 lb
1490262-1 2598-5383-50 Production Torque Wrench 7.9 5/16 15 in.-lbs 2 lb
Figure 1
1. INTRODUCTION
These production torque wrenches are used to properly install or disassemble the connectors listed in Figure 1.
Figure 1 also contains the TE part numbers for the wrenches, the previous part numbers for the wrenches,
wrench size, and the preset torque for each wrench.
NOTE
Dimensions on this sheet are in metric units [with U.S. customary units in brackets], unless otherwise noted.
Reason for revision is provided in Section 5, REVISION SUMMARY.
2. DESCRIPTION
Each production torque wrench contains a protective cover, a torque wrench, and an interchangeable head.
Refer to Figure 2 for the appropriate replacement wrench head part numbers.
The wrenches are designed to be used in the clockwise or counterclockwise direction.
2014 TE Connectivity family of companies TOOLING ASSISTANCE CENTER 1-800-722-1111 This controlled document is subject to change.
1 of 2
All Rights Reserved PRODUCT INFORMATION 1-800-522-6752 For latest revision and Regional Customer Service,
*Trademark visit our website at www.te.com.
TE Connectivity, TE connectivity (logo), and TE (logo) are trademarks. Other logos, product, and/or company names may be trademarks of their respective owners.
ORIGINAL INSTRUCTIONS 408-8676
3. OPERATION OF THE WRENCHES
NOTE
If a wrench has not been used recently, move the wrench head back and forth several times, listening for audibleclicks
Clicking the wrench head back and forth spreads lubricant throughout the internal mechanism to improve wrench
performance.
WRENCH SIZE
TE CONNECTIVITY
PART NUMBER
mm [inches]
1406504-1 6.4 [1/4]
1406504-2 8.0 [5/16]
1406504-3 9.6 [3/8]
1406504-4 12.8 [1/2]
1406504-5 19.6 [3/4]
1406504-6 11.2 [7/16]
1406504-7 7.1 [9/32]
1406504-8 10.4 [13/32]
1406504-9 17.6 [11/16]
1-1406504-0 14.6 [9/16]
1-1406504-1 8.8 [11/32]
1-1406504-2 16.0 [5/8]
1-1406504-3 20.8 [13/16]
1-1406504-4 4.0 [5/32]
1-1406504-5 6.1 [15/64]
Figure 2
Using the appropriate sized head (Figure 1), turn the wrench clockwise (or counterclockwise) until there is an
audibleclick Thisclic indicates that the proper torque has been achieved.
CAUTION
Do NOT over-tighten the connector with the torque wrench. Over-tightening the wrench could result in inaccurate torque
settings.
CAUTION
Do not use or re-terminate damaged connectors.
4. REPLACEMENT
Remove the wrench head by pulling it off the production torque wrench. Then replace the head with the
appropriate head listed in Figure 2.
Order replacement parts through your TE Representative, or call 1-800-526-5142, or send a facsimile of your
purchase order to 717-986-7605, or write to:
CUSTOMER SERVICE (038-035)
TYCO ELECTRONICS CORPORATION
PO BOX 3608
HARRISBURG PA 17105-3608
5. REVISION SUMMARY
Updated document to corporate requirements
Added tolerances to table in Figure 1
2 of 2
Rev G