Application Specification
114-13206
ELCON* Drawer Series Connectors
19 JUL 13 Rev E
NOTE
NOTE
All numerical values are in metric units [with U.S. customary units in brackets]. Dimensions are in millimeters [and inches].
i
Unless otherwise specified, dimensions have a tolerance of 0.13 [.005] and angles have a tolerance of 2. Figures and
illustrations are for identification only and are not drawn to scale.
1. INTRODUCTION
This specification covers the requirements for application of ELCON Drawer Series Connectors: True Hot Plug,
Blind Mating Mixed Signal and Power Connectors. These connectors are designed for use in pluggable wire-to-
board applications of power supplies. The connectors are available in a variety of custom configurations. The pin
side connector accepts pin contacts, and the socket side connector accepts socket contacts. The contact
cavities on both sides of the connector are marked for circuit identification.
The high power connectors are available with or without pre-installed guide pins; mid and low power connectors
are designed with molded-in guide posts to ensure positive mating of connectors. The molded-in pin protectors
prevent damage to the contacts. These features (including the guide pin holes and guide post cavities) have
chamfered edges for ease of mating. The connectors are designed for float-mount and fixed-mount applications
to allow blind mating with misalignment. All connectors are also designed with standoffs to allow easy printed
circuit (pc) board cleaning after soldering.
The contacts accept wire sizes 24 through 1/0 AWG. Contact sizes 20, 16, and 12 are available in crimp type,
and solder type terminations. In addition, contact size 12 is available in hot plug, specifically designed for current
interruption capability. Contact size 0 and 4 is available in crimp type termination, internal thread and external
thread for ring lug mounting and bus bar mounting. Pin contacts (except size 0 and 4) are available in three
lengths: standard, pre mate, and post mate for flexibility in contact sequencing. The contacts contain an active
element, or crown band, which ensures maximum surface contact area, allows even insertion and withdrawal
forces, and provides shock and vibration resistance. The contacts are available in loose piece only. Only crimp
type and threaded contacts are removable.
When corresponding with TE Connectivity Personnel, use the terminology provided in this specification to
facilitate your inquiries for information. Basic terms and features of this product are provided in Figure 1.
Top Drawer 75 Amp Middle Drawer
Socket Side
Pin Side Pin Side Socket Side
Chamfered
Edge
Chamfered
Edge
Mounting
Flange
Contact
Cavities
Pin Protector
Standoffs
Guide Pin Hole Guide Post Guide Post Cavity
Guide Pin
Figure 1 (Contd)
2013 Tyco Electronics Corporation, a TE Connectivity Ltd. company TOOLING ASSISTANCE CENTER 1-800-722-1111 This controlled document is subject to change.
1 of 17
All Rights Reserved PRODUCT INFORMATION 1-800-522-6752 For latest revision and Regional Customer Service,
*Trademark visit our website at www.te.com
TE Connectivity, TE connectivity (logo), and TE (logo) are trademarks. Other logos, product and/or company names may be trademarks of their respective owners. 114-13206
Lower Drawer Mini Drawer
Chamfered
Edge
Pin Side Socket Side
Pin Side Socket Side
Mounting
Flange
Contact
Cavities
Pin Protector
Standoffs
Guide Post Cavity Guide Post
Chamfered Edge
Dual Power Quad Power
Pin Side Socket Side
Pin Side Socket Side
Mounting
Flange
Contact
Cavities
Pin Protector
125 Amp Middle Drawer
Double Drawer
Socket Side
Pin Side
Pin Side Socket Side
Mounting
Flange
Contact
Cavities
Pin Protector
Crimp Type Contact Size 0
Solder Type
Contact
Contact
Crimp Type Internal Thread External Thread
Figure 1 (End)
2. REFERENCE MATERIAL
2.1. Revision Summary
Updated document to corporate requirements and added new logo
Rev E 2 of 17