206638-2-CUT-TAPE TE Connectivity

Catalog 82047 Power Cord Receptacles Revised 6-00 Product Facts n Designed to international standard CEE-22 n Recognized under the Component Recognition Program of Underwriters Laboratories Inc., File No. E28476 n Certified by Canadian Standards Association, File No. LK7189 n VDE approved, License No. 70442 and 70443 n Mate with standard interna- tional plugs n Machine applied, crimp, snap-in contacts n Same contact design for ground and power one inventory item n Rear of housing is egg-crat- ed for maximum protection no post termination sleeving required Photo 42670 Technical Document AMP Power Cord installed in the housing, to them for 250 volts, 10 Instruction Sheets Receptacles are designed provide for proper ground- amperes. to electrical specification ing prior to power engage- 408-7711 Contacts are available in CEE-22, the international ment. 408-7686 - Power Cord strip form for high-speed, standard used by most Receptacle Housing PN They are recognized by automatic machine applica- European nations. 2 0 6 6 3 7 - 1 Underwriters Laboratories tion at lowest cost, and AMP Power Cord recepta- Inc., under the Component loose-piece contacts are Extraction Tool PN 91106-1 cles are available in a 3- Recognition Program, at available for hand tool position and a 5-position 250 volts, 15 amperes when application for repair or Application Specification male configuration with a wired with appropriate 16 maintenance. 114-10044 - Power Cord polarized, thermoplastic AWG 1.25-1.4mm2 wire In addition to economies of Receptacle Housing PN housing suitable for rack or per table 400-5 of the application by automatic 2 0 6 6 3 7 - 1 panel mounting. The crimp, national electrical code. machine, the egg crate snap-in contacts are tin CSA certifies the design at the rear of the plated and have a receptacles for 250 volts, housing cavities eliminates rectangular cross section. 15 amps. Because of the need for costly post-ter- The ground contact extends configuration controls, CEE mination insulation sleeving118 3 farther forward than rates them for 250 volts, the power contacts when 10 amperes. VDE certifies 1976, 1983, 1989 and 2000 Tyco Electronics Corporation All Rights Reserved AMP, AMP-O-LECTRIC, Tyco Trademarks 1 Technical Support Center/AMP FAX Service Dimensions are in www.amp.com Specifications 1-800-522-6752 717-986-7777 inches over millimeters subject to change.Catalog 82047 Power Cord Receptacles Revised 6-00 Materials and Finish 3-Position Housing H o u s i n g Thermoplastic, Part Number 206637-1 9 4 V-0 rated 90 C temperature .008 .130 Dia760 .003 .657 rating black 3.30 19.30 16.69 2 Holes C o n t a c t Brass C o n t a c t Finish Ti n .276 .020 1.969 7.00 0.51 50.01 Receptacle (Ref.) .006 1.564 1.063 .954 0.15 .008 39.98 1.181 27.00 24.23 Dia. 0.20 .276 30.00 Inside Edges 7.00 of Rack .010 .200 .659 .197 0.25 5.08 1.166 R 16.74 5.00 .010 4.22 .880 1.455 0.25 4 Plc. 22.35 36.96 5-Position Housing Part Number 211395-1 .126 Dia003 3.20 .130 Dia006 .157 0.08 3.30 0.15 3.99 2 Holes .006 1.102 .220 R .276 0.15 27.99 5.59 R 7.01 4 Plc006 1.812 1.575 0.15 1.351 46.02 40.00 34.32 Rack Mounting .010 .008 2.260 1.481 0.25 (for 3-Position Housing) 0.20 57.40 37.62 .006 .276 .803 0.15 7.01 Cutout 20.04 .006 .006 .010 .396 .200 .276 .752 0.15 0.15 0.25 .402 .185 10.06 5.08 7.01 .010 R. 1.455 19.10 10.21 4.70 .660 0.25 36.96 .880 16.76 22.35 Pin Contacts .004 .011 .157 .059 0.10 0.28 3.99 1.50 .126 .010 Dia085 3.20 0.25 2.16 1.102 27.99 1.575 .002 .078 .023 Max. 40.00 0.05 1.98 0.58 Panel Mounting (for 3-Position Housing) .147 Min. Wire Insulation Range .080/.135 Dia. 3.73 2.03 - 3.43 Wire Size Range Ins. Dia. Pin Contact Part Number Applicator 1.823 AWG mm2 Range Strip Form Loose Piece Part Number 46.30 .220 R .080-.135 20.16 0.5-1.4 206638-2 206638-3 466136-2 4 Plc. 2.08-3.43 18-14 0.8-2.0 .080-.135 208914-2 567188-2 .752 19.10 Extraction Tool Part Number 91106-1 .126 AMP-O-LECTRIC Dia. 1.524 3.20 38.71 Terminating Machine Rack Mounting (for 5-Position Housing) A complete line of applica- tion tooling is available to meet a wide range of 1.524 38.71 .126 production needs from Dia. 3.20 precision hand tools and .803 .185 R bench-mounted semiauto- 20.04 4 Plc. matic machines to fully 1.823 automatic lead making 46.30 .402 machines. Consult AMP (for 10.21 3-Position Housing) for the Panel Mounting exact machines for specific (for 5-Position Housing) applications. Photo 81169 2 820475MDAS6-00 Technical Support Center/AMP FAX Service Dimensions are in www.amp.com Specifications 1-800-522-6752 717-986-7777 inches over millimeters subject to change.