8 7 6 5 4 3 2 1 THIS DRAWING IS UNPUBLISHED. RELEASED FOR PUBLICATION - REVISIONS ALL RIGHTS RESERVED. COPYRIGHT copyright dateBY - C P LTR DESCRIPTION DATE DWN APVD A1 ECO-17-007675 01JUN2017 GL CP 9 5 (35.54 ) 11 (10) 7 8 D 1. THIS ASSEMBLY CONFORMS TO INTEL PART NO. (SEE TABLE). D 2. EACH ASSEMBLY TESTED FOR OPENS, SHORTS AND SIGNAL INTEGRITY. (23.05 ) 5 3. ROHS AND REACH COMPLIANCE: PRODUCT AND PROCESSING MEETS 1 3 7 THE REQUIREMENTS OF TE SPECIFICATION TEC-138-702. 4. EACH ASSEMBLY PACKAGED IN AN ANTISTATIC BAG. 5 LABEL INFORMATION: (ITEM 9): 2821778-1 (28.85 ) TE PART NUMBER CABLE TYPE SERIAL NUMBER TB= IDENTIFIES TE CONNECTIVITY (M) FT= IDENTIFIES PRODUCT Y= YEAR, WW= WEEK, 66666 SEQUENCE STARTING L AT 00001, RESET EACH WORK WEEK. SERIAL NUMBER BARCODE 39 28 54 6 LABEL INFORMATION (ITEM 10): 2821778-2,-3. (SEE SHEET 2) CABLE TYPE TE PART NUMBER SERIAL NUMBER TB= IDENTIFIES TE CONNECTIVITY 27 1 SERIAL NUMBER BARCODE 39 FT= IDENTIFIES PRODUCT C C Y= YEAR, WW= WEEK, 66666 SEQUENCE STARTING AT 00001, RESET EACH WORK WEEK. 2 4 8 7 FINISH (CONTACT PADS): 30IN MINIMUM GOLD PER TE SPEC 112-162-1 CONNECTOR MARKED WITH OVER 100IN MINIMUM NICKEL PER TE SPEC 112-25-2. CONNECTOR TYPE AND DATE CODE 8 FINISH: 50IN MINIMUM GOLD PER TE SPEC 112-162-5, IN LOCALIZED GOLD PLATE AREA, OVER 50IN MINIMUM NICKEL PER TE 112-25-2 ON 1 28 ENTIRE STOCK. 9 CABLE PART : 023B2LF023 CABLE SPEC: 104-1587. 10. CABLE ASSEMBLY BUILT IN ACCORDANCE WITH INTEL DESIGN GUIDE 1.0 14 15 5.5 REF 11 .CABLE ASSEMBLY LENGTH OFFERED BY TE IS NOT REFERENCED WITHIN INTEL DESIGN 6 GUIDE 1.0 P2 P1 - WRAP (SHEET 2) 60 610 10 2821778-3 6 11 6 WRAP (SHEET 2) 60 460 5 - 2821778-2 11 CABLE PINOUT B B 5 FLAG (SHEET 1) 60 142 5 - 2821778-1 PAIR PIN NAME P1 P2 GROUND BUS - 1 1 2821778-1 LABEL TYPE (M) L INTEL PART NO TE PART NO HFI0 RX DN(1) 2 2 1 HFI0 RX DP(1) 3 3 GROUND BUS - 4 4 GROUND BUS - 28 4 HFI0 RX DN(2) 27 5 2 HFI0 RX DP(2) 26 6 1 1 1 PULL TAB 11 GROUND BUS - 25 7 1 1 - LABEL, WRAP 10 HFI0 RX DN(3) 5 8 3 - - 1 LABEL, FLAG 9 HFI0 RX DP(3) 6 9 GROUND BUS - 25 10 AR AR AR SLEEVING,EXPANDABLE 8 TM HFI0 RX DN(4) 24 11 AR AR AR 7 4 85 OHM TWINAX CABLE, 30AWG 25G TURBO TWIN 9 HFI0 RX DP(4) 23 12 1 1 1 OVERMOLDED STRAIN RELIEF,LECB 6 GROUND BUS - 22 13 1 1 1 OVERMOLDED STRAIN RELIEF,IFP 5 GROUND BUS - 7 14 GROUND BUS - 8 15 1 1 1 DUST COVER, LECB (NOT SHOWN) 4 HFI0 TX DP(4) 9 16 1 1 1 DUST COVER, IFP (NOT SHOWN) 3 5 HFI0 TX DN(4) 10 17 1 1 1 LEC 54B RECPT, 54 POSN 2 GROUND BUS - 21 18 1 1 1 IFP PLUG, 28 POSN 1 HFI0 TX DP(3) 20 19 6 HFI0 TX DN(3) 19 20 ITEM DESCRIPTION -3 -2 -1 A A NO GROUND BUS - 11 21 DWN 15JUL2016 HFI0 TX DP(2) 12 22 THIS DRAWING IS A CONTROLLED DOCUMENT. T.SMITH 7 TE Connectivity CHK 15JUL2016 HFI0 TX DN(2) 13 23 C.POGASH DIMENSIONS: TOLERANCES UNLESS APVD NAME OTHERWISE SPECIFIED: - GROUND BUS - 14 24 - mm IFP ASSEMBLY, TYPE B, RIGHT EXIT PRODUCT SPEC 0 PLC - GROUND BUS - 18 24 1-PORT, NON-INVERTED. 1 PLC 0.5 - 2 PLC 0.13 HFI0 TX DP(1) 17 25 - 3 PLC APPLICATION SPEC 0.013 8 4 PLC - SIZE CAGE CODE DRAWING NO RESTRICTED TO HFI0 TX DN(1) 16 26 ANGLES - - MATERIAL FINISH WEIGHT GROUND BUS - 15 27 - 2821778 - - A1 - - SCALE SHEET OF REV - - CUSTOMER DRAWING 1:1 1 2 A1 4805 (3/13) LEC54B YYWW8 7 6 5 4 3 2 1 THIS DRAWING IS UNPUBLISHED. RELEASED FOR PUBLICATION - REVISIONS ALL RIGHTS RESERVED. COPYRIGHT copyright dateBY - C P LTR DESCRIPTION DATE DWN APVD SEE SHEET 1 D D 10 6 C C (M) L 2821778-2,-3 WRAP AROUND LABEL REQUIREMENT ALL ASSEMBLY REQUIREMENTS B B SAME AS -1 EXCEPT FOR LABEL A A DWN 15JUL2016 THIS DRAWING IS A CONTROLLED DOCUMENT. T.SMITH TE Connectivity CHK 15JUL2016 C.POGASH DIMENSIONS: TOLERANCES UNLESS APVD NAME OTHERWISE SPECIFIED: - - mm IFP ASSEMBLY, TYPE B, RIGHT EXIT PRODUCT SPEC 0 PLC - 1-PORT, NON-INVERTED. 1 PLC 0.5 - 2 PLC 0.13 - 3 PLC APPLICATION SPEC 0.013 4 PLC - SIZE CAGE CODE DRAWING NO RESTRICTED TO ANGLES - - MATERIAL FINISH WEIGHT - 2821778 - - A1 - - SCALE SHEET OF REV - - CUSTOMER DRAWING 1:1 2 2 A1 4805 (3/13)