KISSLING SINGLE POLE BI-STABLE RELAYS Series 30 / 300A - from TE Connectivity (TE) The series 30 bi-stable relay meets even the most difficult operating requirements and is suited for various applications in severe conditions on commercial vehicles, buses, construction & agricultural vehicles, ground support equipment and fork lifts. These relays are available with a wide variety of configuration options including different contact configurations and coil voltages to have the right product for your needs. Other important advantages are low heat generation in the contact area based on low contact voltage drop, a compact design, silver alloy contact material and the use of mechanical and high thermal stability Features insulating compounds. Both the terminals and the housing are protect- Sealed housing conforms to IP6K9K ed against corrosion. Furthermore, our relays are characterized by high Robust design shock and vibration characteristics and a low voltage drop. Variety of configuration options By equipping the relays with blow-out magnets, contact voltages up to 6G shock and 4G vibration resistant 250VDC are possible. The use of blow-out magnets is recommended Main contact current rated for continu- for contact voltages over 40VDC and blow-out magnets are also rec- ous current and 100% duty cycle ommended for inductive load applications to maintain long contact life at all voltages. Applications Commercial vehicles Bus Lift truck Ground support equipment Construction and agricultural vehicles Circuits NO-Contact NO-Contact NO/NC-Contact NO-Contact Standard type Special type reversed polarity Auxiliary contact common - common + / Magnetic blowout 87y 87b 88y 88b 88 88a 88 88a 88 88a 87 87a 88 88a 86a 85a 86a 86a 85 86 85 85 86b 85b 86b 86b Suppression diode Suppression diode Suppression diode Suppression diode 30-200-50 30-200-59 30-200-50 30-200-50 Industrial & Commercial Transportation / Series 30 - 300A Page 1SERIES 30 300A Specification Technical Data Temperature range -40C to +85C Protection IEC 60529 / DIN 40050-9 / IP67 (0,2bar 1min) and IP6K9K Shock 6g / 11msec Vibration 4g / 50 - 2000Hz Thread sizes / Torque M4 = 2.0 - 2.2Nm M10 = 15 - 20Nm Electrical Characteristics Min. Insulation resistance 100M After live or environment 50M Dielectric withstanding voltage 1050VAC / 1min at 50Hz Max. Contact drop, initial 150mV Contact drop after life test 175mV Continuous current 300A Overload 2400A - 1sec / 600A - 20sec Rated contact load 12 and 24 / 28VDC Resistive load 50.000 cycles 300A Mechanical life 100.000 cycles Coil Data 12VDC 24 / 28VDC 24VDC NO/NC 36VDC Voltage range 9-16VDC 18-32VDC 18-32VDC 27-48VDC Nominal voltage 12VDC 28VDC 28VDC 36VDC Pick up voltage 9VDC 13VDC 13VDC 20VDC Drop out voltage min. 7VDC 10VDC 10VDC 15VDC Pull in coil resistance 1.8 20% 7.8 20% 4.1 20% 18 20% Pull in current approx. 6.6A 3.0A 6.8A approx. 1.9A Drop out coil resistance 2.0 20% 8.4 20% 6.4 20% 21.8 20% Drop out current approx. 6.0A 2.8A 4.4A approx. 1.6A Pick up impulse time approx.* 50ms 50ms 50ms 50ms Drop out impulse time approx.* 50ms 50ms 50ms 50ms * (continuous impulse max.1 min) Operating times NO-Contact Changeover NO-Contact Changeover NC-Contact Operate max. 15msec max. 25msec max. 30msec Bounce max. 5msec max. 5msec max. 8msec Release max. 10msec max. 20msec max. 35msec 2 Wire Section min. 95mm / 0.147 sq.inch / AWG 4-0 Mounting position optional Industrial & Commercial Transportation / Series 30 - 300A Page 2