3-1393136-5 TE Connectivity

Catalog 1308242 Issued 3-03 P&B CD series CMOS IC Time Delay Relay 1% Repeatability Operates from -40C to +55C Delay on operate or delay on release timing modes Fixed, knob or resistor adjustable types Calibrated dial on knob adjustable types 10A output relay with SPDT or DPDT contacts Various models time from 0.1 to 180 sec. File E22575 File LR15734 Users should thoroughly review the technical data before selecting a product part number. It is recommended that user also seek out the pertinent approvals files of the agencies/laboratories and review them to ensure the product meets the requirements for a given application. Initial Dielectric Strength Timing Modes Between Open Contacts: 500V rms, 60 Hz. Delay on operate Delay period begins when input voltage is applied. At Between All Other Conductors: 500V rms, 60 Hz. the end of the delay period, the relay will operate and will not release until input voltage is removed. Reset occurs when input voltage is reapplied. INPUT ON VOLTAGE OFF N.O. RELAY ON TIME CONTACTS OFF Input Data 25C Voltage: 24 & 120VAC and 12 through 110VDC. Delay on release Input voltage must be applied continuously to operate Power Requirement: AC Types: Typically less than 3 VA. the internal relay. When control Input is applied, the relay energizes. DC Types: Typically less than 3 W. When control input is removed, timing begins. When timing is complete, Transient Protection: Yes. the relay will de-energize. Time may be reset to zero during timing by Reverse Voltage Protection: Yes. reapplying control input. Input Voltages & Limits 25C Voltage Nominal Minimum Maximum CONTROL ON Type Voltage Voltage Voltage INPUT OFF N.O. RELAY ON AC 24 20 28 TIME CONTACTS OFF 120 105 130 12 11 13 DC 24 20 32 48 41 55 110 95 125 Note: DC voltage must be filtered (5% p-p ripple max. at nom. voltage). AC models will operate on 50 or 60 Hz. Timing Specifications Timing Ranges: From 0.1 to 180 sec. Timing Adjustment: Fixed, external resistor and knob adjustable. Tolerance (for AC units add 1/2 cycle 60 Hz.): Knob Adj. Types: 5% of max. specified at high end of timing range min. specified, or less, at low end 10% full scale. Fixed Types: 5%. Res. Adj. Types: 5% at high end of timing range min. specified, or less, Environmental Data at low end. Temperature Range: Storage: -55C to +85C. Delta Time (for AC units add 1 cycle 60 Hz.): 5%. Operating: -40C to +55C. Repeatability (for AC units add 1 cycle 60 Hz.): 1%. Release Time: 45 ms, typ. 60 ms, max. Recycle Time: 45 ms, typ. 60 ms, max. Mechanical Data Contact Data 25C Termination: 8- or 11-pin octal style plug. Arrangements: 2 Form C (DPDT). Enclosure: Yellow plastic case. Knob adjustable types have dial scale Material: Silver-cadmium oxide alloy. calibrated in seconds 5%. Rating: 10A 30VDC or 277VAC, resistive 1/2 HP 250VAC 1/3 HP Sockets: Models with 8-pin base fit either 27E122 or 27E891 (snap-on) 120VAC. screw terminal sockets. 11-pin types fit either 27E123 or Expected Mechanical Life: 10 million operations. 27E892 (snap-on) screw terminal sockets. Expected Electrical Life: 100,000 operations, min., at rated load. Weight: 8 oz. (227g) approximately. Dimensions are shown for Dimensions are in inches over Specifications and availability www.tycoelectronics.com reference purposes only. (millimeters) unless otherwise subject to change. Technical support: 1222 specified. Refer to inside back cover.Catalog 1308242 Issued 3-03 P&B Ordering Information Authorized distributors are more likely to stock boldface items listed below. Delay on Operate Models Delay on Release Models Voltage Time Adjustment Wiring Dia. Part Number Voltage Time Adjustment Wiring Dia. Part Number 0.1 to 1 Sec. CDB-38-70001 0.1 to 1 Sec. CDB-38-70016 0.1 to 5 Sec. CDB-38-70002 0.1 to 5 Sec. CDB-38-70091 120VAC 0.1 to 10 Sec. Knob 1 CDB-38-70003 120VAC 0.1 to 10 Sec. Knob 3 CDB-38-70014 0.3 to 30 Sec. CDB-38-70006 0.3 to 30 Sec. CDB-38-70092 0.6 to 60 Sec. CDB-38-70004 0.6 to 60 Sec. CDB-38-70012 1.8 to 180 Sec. CDB-38-70005 1.8 to 180 Sec. CDB-38-70015 120VAC 1 Sec. Fixed CDA-38-70012 120VAC 1 Sec. Fixed 3 CDA-38-70025 0.1 to 1 Sec. CDF-38-70001 12VDC 180 Sec. Fixed 3 CDC-38-20026 120VAC 0.1 to 5 Sec. Resistor 2 CDF-38-70002 0.1 to 10 Sec. CDD-38-30014 0.1 to 10 Sec. CDF-38-70003 24VDC 0.6 to 60 Sec. Knob 3 CDD-38-30012 0.1 to 10 Sec. CDD-38-30003 1.8 to 180 Sec. CDD-38-30008 24VDC 0.6 to 60 Sec. Knob 1 CDD-38-30004 1.8 to 180 Sec. CDD-38-30005 48VDC 0.6 to 60 Sec. Knob 1 CDD-38-40002 0.1 to 1 Sec. CDD-38-60004 110VDC 0.1 to 10 Sec. Knob 1 CDD-38-60001 0.6 to 60 Sec. CDD-38-60002 1.8 to 180 Sec. CDD-38-60003 Outline Dimensions 2.406 MAX. (61.1) .56 2.937 MAX. 1.781 MAX60 (14.2) (74.6) (45.2) (15.2) Wiring Diagrams Bottom Views (pins numbered clockwise from keyway) CONTROL INPUT* EXTERNAL RESISTOR + + SUPPLY + + INPUT INPUT INPUT (DC POLARITY INDICATED)** (DC POLARITY INDICATED)** (DC POLARITY INDICATED)** Fig. 1 Fig. 2 Fig. 3 8 Pin 11 Pin 11 Pin * If control input is applied when supply input is applied, relay will immediately energize. A 50 millisecond minimum control pulse is required. ** Note Input polarity for DC operation. For most reliable operation on AC, connect high side to + and low side to . External Resistor Selection Chart See External Resistor Selection Charts at beginning of Time Delay Relay section of this Databook. Dimensions are shown for Dimensions are in inches over Specifications and availability www.tycoelectronics.com reference purposes only. (millimeters) unless otherwise subject to change. Technical support: 1223 specified. Refer to inside back cover.