Automotive Relays Plug-in Micro ISO Relays Micro Relay Low Noise Noise level below 50dBA Pin assignment according to ISO 7588 part 3 Plug-in terminals Customized versions on request Special marking Special covers (e.g. notches, release features) Typical applications Cross carline up to 20A for example: front and rear wiper, air condition, interior fan. F145 fcw1 bw Contact Data Coil Data Contact arrangement 1 form A, 1 NO 1 form C, 1 CO Rated coil voltage 12VDC Rated voltage 12VDC 12VDC Limiting continuous current NO/NC Coil versions, DC coil 23C 20A 20/15A Coil Rated Operate Release Coil Rated coil 4) 4) 85C 15A 15/10A code voltage voltage voltage resistance power 125C 8A 8/5A VDC VDC VDC 10% mW 1) Limiting making current 100A 40A *01-402 12 7.2 1.4 181 796 1) Limiting breaking current 30A 30A *01-403 12 7.2 1.4 254 567 4) Without components in parallel. Limiting short-time current 2) All figures are given for coil without pre-energization, at ambient temperature +23C. overload current, ISO 8820-3 1.35 x 20A, 1800s 2.00 x 20A, 5s Coil operating range 3.50 x 20A, 0.5s TE074 OVR1 6.00 x 20A, 0.1s Jump start test 24VDC for 5min, conducting nominal curr ent at 23C Contact material silver based 3) Min. recommended contact load 1A at 5VDC Initial voltage drop NO contact at 10A, typ./max. 15/300mV 50/300mV NC contact at 10A, typ./max. - 50/300mV Frequency of operation 6 ops./min (0.1Hz) Does not take into account Electrical endurance, resistive load at 14VDC the temperature rise due to 5 15A >1x10 ops. the contact current 6 Mechanical endurance typ. 10 ops. E = pre-energization 1) The values apply to a resistive or inductive load with suitable spark suppression and at maximum 13.5 VDC for 12VDC nominal voltages. For a load current duration of maximum 3s for a make/break ratio of 1:10. 2) Current and time are compatible with circuit protection by a typical automotive fuse. Relay will make, carry and break the specified current. 3) See chapter Diagnostics of Relays in our Application Notes or consult the internet at Automotive Relays Plug-in Micro ISO Relays Micro Relay Low Noise (Continued) Other Data Other Data (continued) EU RoHS/ELV compliance compliant Terminal type plug-in, QC Ambient temperature -40 to +125C Cover retention Climatic cycling with condensation, axial force 150N EN ISO 6988 6 cycles, storage 8/16h pull force 150N Temperature cycling, push force 200N IEC 60068-2-14, Nb 10 cycles, -40/+85C (5C/min) Terminal retention Damp heat cyclic, pull force 100N IEC 60068-2-30, Db, Variant 1 6 cycles, upper air temp. 55C push force 100N 6) Damp heat constant, IEC 60068-2-3, Ca 56 days resistance to bending 10N 6) Category of environmental protection, force applied to side 10N IEC 61810 RT I dustproof torque 0.3Nm Degree of protection, IEC 60529 IP54 Weight approx. 15g (0.5oz) Corrosive gas Packaging unit 240 pcs. 3 3 5) No change in the switching state >10s. Valid for NC contacts, NO contact values IEC 60068-2-42 102cm /m SO , 10 days 2 3 3 significantly higher. IEC 60068-2-43 10.3cm /m H S, 10 days 2 6) Values apply 2mm from the end of the terminal. When the force is removed, the terminal Vibration resistance (functional) must not have moved by more than 0.3mm. 5) IEC 60068-2-6 (sine sweep) 10 to 500Hz min.5g Shock resistance (functional) 5) IEC 60068-2-27 (half sine) min. 30g 6ms Accessories Drop test, free fall, IEC 60068-2-32 1m onto concrete For details see datasheet Connectors for Micro ISO Relays 23 max 15.5 max Terminal Assignment NOR COD 1 form A, NO with resistor 1 form C, 1 CO with diode 25.4 max 24.1 0.2 2 5 2 54 Measurement reference plane 5x 11.2 0.3 0.2 0.8 0.05 4.8 0.1 6.3 0.1 1 3 1 3 Quick connect terminal similar to ISO 8092-1 Dimensions View of the terminals (bottom view) 23 max 15.5 max 11.4 0.2 4.5 0.15 1 7.65 0.2 25.4 max 24.1 0.2 3 5 4 4.5 0.15 2 Measurement reference plane 8 0.15 6 0.15 5x 11.2 0.3 0.2 Positional tolerances 0.15 145 DD 2 0.8 0.05 4.8 0.1 6.3 0.1 Quick connect terminal similar to ISO 8092-1 2 09-2017, Rev. 0917 Catalog and product specification according Catalog and product data is subject to the Catalog product data, Definitions section, 11.4 0.2 www.te.com to IEC 61810-1 and to be used only together terms of the disclaimer and all chapters of application notes and all specifications are 4.5 0.15 2017 TE Connectivity. with the Definitions section. the Definitions section, available at subject to change. 1 7.65 0.2