33-012C TE Connectivity

Catalog 1308242 Issued 3-03 (PDF Rev. 8-04) P&B W58 series Push To Reset Only Thermal Circuit Breaker Features Maximum Resistance vs. Current Rating +25C 0.5 amp to 30 amp ratings. Current Maximum Current Maximum Cannot be manually tripped. Rating Resistance Rating Resistance Button extends for visual trip indication. in Amps in Ohms in Amps in Ohms Push button to reset breaker. 0.5 5.0 8 0.020 Termination is screw or .250 QC. 1 1.35 9 0.020 2 0.32 10 0.014 3 0.18 12 0.010 4 0.10 15 0.010 Agency Approvals 5 0.026 20 0.005 W58 Series is UL 1077 Recognized as Supplementary Protectors, File 6 0.026 25 0.006 E69543, and CSA Certified as Appliance Component Protectors, File 7 0.020 30* 0.004 LR15734. *No UL/CSA Users should thoroughly review the technical data before selecting a product part number. It is recommended that users also seek out the pertinent approvals files of the agencies/laboratories and review them to ensure the product meets the requirements for a given application. Electrical Data +25C Mechanical/Environmental Data Calibration: Breaker will continuously carry 100% of rated load. It may trip Shock: Withstands to 10g. between 101% and 145% of rated load, but must trip at Endurance Cycling: Over 1,000 cycles at 200% of rated load. 145% at 25C. Vibration: Withstands to 10g at 10-55 Hz. Dielectric Strength: Over 1,500 volts RMS. Weight: Less than 1 1/2 oz. (42.5g). Maximum Operating Voltages: 50VDC 250VAC. Interrupt Capacity: 2,000 amps at 50VDC (0.5 - 30 amp models). 1,000 amps at 250VAC (0.5 - 30 amp models). Note: 30 0amp model not UL or CSA. Resettable Overload Capacity: Ten times rated current. Time vs. Current Trip Curve +25C Ambient Compensation Chart 1000 1.40 (A) All 5-30 Amp Models (B) All 1-4 Amp Models Overload Trip Times Overload Trip Times 900 1.30 100% No Trip 100% No Trip (A) 145% Trip in 1 hour 145% Trip in 1 hour 1.20 800 200% 6.0-30 Sec. 200% 10-45 Sec. 400% 1.6-4.5 Sec. 400% 3.0-14.0 Sec. 1.10 600% 0.60-1.7 Sec. 600% 1.4-7.0 Sec. 700 800% 0.25-0.90 Sec. 800% 0.75-4.3 Sec. 1000% 0.15-0.65 Sec. 1000% 0.50-3.4 Sec. 1.00 600 0.90 500 0.80 (B) 400 0.70 300 0.60 20 10 0 102030405060 200 Ambient Temperature In Degrees Centigrade (C) 100 0 To use this chart: Read up from the ambient .1 1 10 100 1000 temperature to the curve, and across to find a correction Time In Seconds factor. Multiply the breaker rating by the correction factor to determine the compensated rating. Calculate the overloads in terms of the compensated rating to use the published trip curve. Dimensions are shown for Dimensions are in inches over Specifications and availability www.tycoelectronics.com reference purposes only. (millimeters) unless otherwise subject to change. Technical support: 107 specified. Refer to inside back cover. Load Current As A Percent Of Breaker Rating Correction FactorCatalog 1308242 Issued 3-03 (PDF Rev. 8-04) P&B Ordering Information Typical Part No. B W 58 -X B 1A4A -5 1. Designator: W = Circuit breaker 2. Series Number: 58 = Single Pole, Push-to-Reset 3. Circuit Function: X = Series Trip 4. Button: A = White, plain, no rate marking, no trip band E = White with red rate marking no trip band B = White with red rate marking, red trip band F = White with black rate marking, no trip band C = White with black rate marking, red trip band 5. Mounting Bushing: 1 = 7/16 x .500 (12.70mm) long 4 = 15/32 x .300 (7.62mm) long, black 6 = 3/8 x .465 (11.81mm) long, round 6. Terminals: A = Quick connect .250 (6.35mm) straight C = 6/32 screw 90 (screws installed) D = 6/32 screw 90 (screws bulk packed) 7. Mounting Hardware: 4 = Knurled nut/hex nut 15 = Two hex nuts/lock washer 6 = Knurled nut/hex nut/lock washer 99 = No mtg. hardware supplied (Use C, Step 8) 12 = Knurled nut/lock washer Note: For other hardware combinations, order separately. See mounting hardware Ordering Information table. 8. Mounting Hardware Packaging: A = Assembled to bushing B = Bulk unassembled C = No mounting hardware 9. Specify Amp Rating: 0.5 3 6 9 15 30* 1 4710 20 2 5812 25 *Not UL or CSA Stock Items Authorized distributors are more likely to stock the following items. W58-XB1A4A-1 W58-XB1A4A-6 W58-XB1A4A-15 W58-XC4C12A-2 W58-XC4C12A-15 W58-XB1A4A-2 W58-XB1A4A-7 W58-XB1A4A-20 W58-XC4C12A-3 W58-XC4C12A-20 W58-XB1A4A-3 W58-XB1A4A-8 W58-XB1A4A-25 W58-XC4C12A-5 W58-XC4C12A-25 W58-XB1A4A-4 W58-XB1A4A-10 W58-XB1A4A-30 W58-XC4C12A-7 W58-XC4C12A-30 W58-XB1A4A-5 W58-XB1A4A-12 W58-XC4C12A-1 W58-XC4C12A-10 Outline Dimensions Terminal Options .250 (6.35) x .032 (.81) .050 MAX. QUICK CONNECT TERMINALS .440 1.375 (1.27) (11.18) (34.93) CLOSED POSITION .415 (10.54) CODES 1 & 4 .425 .425 (10.80) .850 .312.005 1.375 1.375 (10.80) 15 (7.92.13) (21.59) (34.93) (34.93) .250 .850 (6.35) (21.59) .440 CODE 6 A (11.18) SEE TERMINAL DRAWINGS SEE MOUNTING FOR DETAIL BUSHING AND .187 MOUNTING HARDWARE DRAWINGS FOR DETAIL (4.75) .281 MAX. (7.14) OPEN POSITION .660 .312 TYP. (16.76) (7.92) BUTTON .156 C & D .85 (3.96) (21.6) 6-32 SCREW & LOCK WASHER ASSEMBLY Dimensions are shown for Dimensions are in inches over Specifications and availability www.tycoelectronics.com 108 reference purposes only. (millimeters) unless otherwise subject to change. Technical support: specified. Refer to inside back cover.