3SBC2126A2 TE Connectivity

CII Low Signal Relays CII Low Signal Relays Double Pole, Electrically Held, 2 Amps and Less (Continued) Electrical Characteristics Operating Characteristics .150 Grid-space Relays Contact Ratings Operate Time 4 ms max. Type 3SBC (2PDT) Standard DC resistive 2 amps at 28 volts Release Time 4 ms max. 1 (50,000 operations) 135 mW 2PDT Contact Bounce 1.5 ms 1 Amp 28 V (100,000 operations) 50 mW (Form AB) Dielectric Strength DC inductive 0.5 amps at 28 volts, 1 PNC1 PNO 500 volts rms at sea level 200 mH 350 volts rms at 70,000 feet and above AC resistive 0.5 amps at 115 volts Insulation Resistance 1,000 AC 0.125 amps at 115 volts (case Product Facts megohm min. over temperature range grounded) Low-level 50 A at 50 mV n Low profile only Environmental Characteristics Peak AC or DC 0.32 inches high Vibration 30G, to 3000 Hz Contact Resistance n Internal diode for coil Shock 100 G at 11 ms 0.050 ohms max. 0.150 ohms after life The .150 Grid-space relay transient suppression and Temperature -65C to +125C test only 0.32 inches high transistor driven models Life 100,000 operations at rated See page 1-44 for Mounting Forms, saves space in electronic available loads listed 1,000,000 operations at Terminals and Circuit Diagrams. packaging. The pin spacing low-level loads n Qualified to MIL-R-39016/13 allows you to insert the relay with no intermediate pin n RF designs available spreaders as well as meet applicable military specifications. *Values listed are factory test and inspection data. User should allow for meter variations. At nominal resistance plus 10%. Applicable over the operating temperature range in circulating air. See Page 1-42 for ordering instructions. * The part number example shown on this page is for catalog items. For a list of specific QPL part numbers, please see the index in Section 15. 1-41 Catalog 5-1773450-5 Dimensions are shown for Dimensions are in millimeters USA: +1 800 522 6752 For additional support numbers Revised 3-13 reference purposes only. unless otherwise specified. Asia Pacific: +86 0 400 820 6015 please visit www.te.com Specifications subject UK: +44 800 267 666 www.te.com to change.CII Low Signal Relays Double Pole, Electrically Held, 2 Amps and Less (Continued) Electrical Characteristics Operating Characteristics .150 Grid-space Contact Ratings Operate Time 4 ms max. Hybrid Relays DC resistive 2 amps at 28 volts Release Time 6 ms max. Single Diode, Dual Diode (50,000 operations) Contact Bounce 1.5 ms 1 Amp 28 V (100,000 operations) Type 3SBC (2PDT) Dielectric Strength (Note 1) DC inductive 0.5 amps at 28 volts, 500 volts rms at sea level 135 mW 200 mH 350 volts rms at 70,000 feet and above AC resistive 0.5 amps at 115 volts Insulation Resistance (Note 1) AC 0.125 amps at 115 volts (case 1,000 megohm min. over temperature grounded) Product Facts range Low-level 50 A at 50 mV n Low profile only Peak AC or DC Environmental Characteristics 0.32 inches high Contact Resistance Vibration 30G, to 3000 Hz 0.050 ohms max. 0.150 ohms after life n 50 milliwatt forms available The hybrid .150 Grid-space Shock 100 G at 11 ms test relay only 0.32 inches n Qualified to MIL-R-39016/37 Temperature -65C to +125C Life 100,000 operations at rated high saves space in loads listed 1,000,000 operations at n Qualified to MIL-R-39016/38 Semiconductor Characteristics electronic packaging. The low-level loads at 25C pin spacing allows you to n RF designs available Diode insert the relay with no inter- Max. Negative Transient 1.0 volt mediate pin spreader. Breakdown Voltage 100 VDC 10 A Max. Leakage Current 1 A 50 VDC See page 1-44 for Mounting Forms, Terminals and Circuit Diagrams. Note: Relays specified by catalog Ordering Instructions numbers (per above directions) are Example: The relay selected in the general use items controlled by cat- example is a FORM AB .150-grid alog specifications. Relays to be relay, current calibrated, end controlled by customer drawings bracket mounting with 0.13-inch or relays having requirements not solder hook header, 210 ohms coil covered in this publication will resistance, and 50 mW sensitivity. be assigned special catalog num- By choosing the proper code for bers upon request. each of these relay characteristics, the catalog number is 3SBC6131E2. The letter R following sensitivity code indicates relay received 5000 operation miss-test. Ex. 3SBC6131E2R. * The part number example shown on this page is for catalog items. For a list of specific QPL part numbers, please see the index in Section 15. 1-42 Catalog 5-1773450-5 Dimensions are shown for Dimensions are in millimeters USA: +1 800 522 6752 For additional support numbers Revised 3-13 reference purposes only. unless otherwise specified. Asia Pacific: +86 0 400 820 6015 please visit www.te.com Specifications subject UK: +44 800 267 666 www.te.com to change.