Instruction Sheet UniversalHandToolAssemblies 408--7141 465629-1and -2 16 MAR 12 RevB PROPERUSEGUIDELINES CumulativeTraumaDisorderscanresultfromtheprolongeduseofmanuallypoweredhandtools.Handtoolsareintendedforoccasionaluseandlowvolume applications.Awideselectionofpoweredapplicationequipmentforextended--use,productionoperationsisavailable. Type U Drive Screw Handle Strap Tip Holder Handle Strap Holding Screw TIP INSTRUCTIONSHEET PRODUCT 465645-- 408--9749 Wrap Type Tab Receptacle Contact 465665--1 408--9580 250 SeriesFASTIN--FASTON* Terminal 110, 187, 205, and 250 SeriesFASTON* Terminals (With Wire Insulation Diameter or Crimp Width of 2.41 mm .095 in. or Less) 446546865468---- 408408----71447144 All Tab--LokFlag FASTON Terminals 110, 187, 205, and 250 SeriesFASTON Terminals 465488-- 408--7144 (With Wire Insulation Diameter or Crimp Width Over 2.41 mm .095 in. ) Figure 1 1. INTRODUCTION 2. DESCRIPTION The hand tool assembly consists of a handle, handle Universal Hand Tool Assemblies 465629--1 and --2 strap, strap holding screw, tip holder, and Type U areusedwiththetipslistedinFigure1toinsertor drive screw. The tip holder of Tool --1 is shorter than extract the products also listed in Figure 1. The tips that of Tool --2 to accommodate the depth of the are not included with the tool. Refer to the tip application (refer to Figure 3 for length). instruction sheet for the product insertion or extraction procedure. 3. USINGTHETOOL Dimensions in this instruction sheet are in metric NOTE 3.1. AdjustingtheHandleStrap units with U.S. customary units in brackets . 1. Move the strap so that the wide part of the hole Figures are not drawn to scale. i is under the strap holding screw. Reasons for reissue of this instruction sheet are 2. Lift the strap off the strap holding screw, and provided in Section 6, REVISION SUMMARY. adjust it to the size desired. E2012 Tyco Electronics Corporation, a TE Connectivity Ltd. Company TOOLING ASSISTANCE CENTER 1--800--722--1111 This controlled document is subject to change. 1 of 2 All Rights Reserved PRODUCT INFORMATION 1--800--522--6752 For latest revision and Regional Customer Service, *Trademark visit our website at www.te.com LOCB TE Connectivity, TE connectivity (logo), and TE (logo) are trademarks. Other logos, product and/or Company names may be trademarks of their respective owners. ORIGINAL INSTRUCTIONS408-7141 3.2. InstallingtheTip 5. REPLACEMENTANDREPAIR Customer--replaceable parts are provided in Figure 3. 1. Select the proper tip according to Figure 1. A complete inventory should be stocked and controlled to prevent lost time when replacement of 2. Place the tip on the tool tip holder so that the parts is necessary. Parts other than those listed are slot fits through the Type U drive screw of the tip not repairable. Order replacement parts or new tools holder. See Figure 2. through your TE Connectivity Representative, or call 1--800--526--5142, or send a facsimile of your 3. Keeping the tip and tip holder aligned, push the purchase order to 717--986--7605, or write to: tip toward the tool until the tip locks in the tip CUSTOMER SERVICE (038--035) holder. TYCO ELECTRONICS CORPORATION PO BOX 3608 HARRISBURG PA 17105--3608 Type U Drive Screw Tip (Ref) Handle Strap 465430--1 PushTiptoLockinPlace Type U Drive Screw 2--21017--4 Tip Holder Figure 2 A 3.3. RemovingtheTip TOOL DIMENSIONA To remove the tip from the tool, pull the tip straight from of the tip holder, and lift it off of the Type U drive 465629--1 47.5 1.87 screw. 465629--2 149.1 5.87 Figure 3 4. MAINTENANCEANDINSPECTION 6. REVISIONSUMMARY Ensure that the tool is clean and undamaged, and that no contaminants become lodged in the tip holder. S New logo The tool should be inspected before each use. 2 of 2 Rev B