Application Specification 114--13033 AUGAT*HOLTITE*Sockets 14 MAR 11 Rev B All numerical values are in metric units with U.S. customary units in brackets . Dimensions are in millimeters and NOTE inches . Unless otherwise specified, dimensions have a tolerance of +0.13 +.005 and angles have a tolerance of +2 . Figures and illustrations are for identification only and are not drawn to scale. i 1. INTRODUCTION This specification covers the requirements for application of AUGAT HOLTITE Sockets. These manually applied or reel--mounted machine applied solderless spring sockets are designed to be contained within the barrel of a plated--through hole. The design allows the socket and plated--through hole to form a zero--profile component socket which provides an interconnect for a broad range of electronic parts and components. The sockets are available in a variety of different series and sizes based on printed circuit (pc) board hole diameter. They are also available normally on mylar strips which can be reeled on custom socket patterns for ease of application. When corresponding with TE Connectivity (TE) Personnel, use the terminology provided in this specification to facilitate your inquiries for information. Basic terms and features of this product are provided in Figure 1. Entry Area Locking Collar Groove Transition Region Fingers Figure 1 2. REFERENCEMATERIAL 2.1. RevisionSummary S Updated document to corporate requirements S New logo 2.2. CustomerAssistance Reference Part Number 6--1437514--7 and Product Code E354 are representative numbers of AUGAT HOLTITE Sockets. Use of these numbers will identify the product line and expedite your inquiries through a service network established to help you obtain product and tooling information. Such information can be obtained through a local TE Representative or, after purchase, by calling the Tooling Assistance Center or Product Information number at the bottom of this page. E2011 Tyco Electronics Corporation, a TE Connectivity Ltd. Company TOOLING ASSISTANCE CENTER 1--800--722--1111 This controlled document is subject to change. 1 of 7 All Rights Reserved PRODUCT INFORMATION 1--800--522--6752 For latest revision and Regional Customer Service, TE logo is a trademark. visit our website at www.te.com LOC B *Trademark. Other product names, logos, or company names might be trademarks of their respective owners.114-13033 2.3. Drawings Customer Drawings for specific products are available from the service network. The information contained in Customer Drawings takes priority if there is a conflict with this specification or with any other technical documentation supplied by TE. 2.4. Specifications Product specification 108--1979 provides product performance requirements and test information. 2.5. InstructionalMaterial The following list includes available instruction sheets (408--series) that provide assembly procedures for operation, maintenance and repair of tooling and customer manuals (409--series) that provide setup, operation, and maintenance of machines. Document Number Document Title 408--3295 Preparing Reel of Contacts for Application Tooling 408--6732 Pneumatic Auto--Cycle Unit 91112--3 408--6923 Manual Arbor Frame Assembly 58024--1 408--7777 Manual Arbor Frame Assembly 91085--2 408--9816 Handling of Reeled Products 409--5626 SM--3 Machine No. 814700-- 3. REQUIREMENTS 3.1. Storage A. UltravioletLight Prolonged exposure to ultraviolet light may deteriorate the chemical composition used in the socket. B. ShelfLife The sockets should remain in the shipping containers until ready for use to prevent deformation to the sockets. The sockets should be used on a first in, first out basis to avoid storage contamination that could adversely affect signal transmissions. C. ChemicalExposure Do not store sockets near any chemicals listed below, as stress corrosion cracking in the sockets may occur. Alkalies Ammonia Citrates Phosphates Citrates Sulfur Compounds Amines Carbonates Nitrites Sulfur Nitrites Tartrates 3.2. Material All sockets are made of beryllium--copper with gold, tin/lead, or tin plating. 3.3. PCBoards A. MaterialandThickness 1. Board material will be glass epoxy (FR--4, G--10). 2. Board thickness shall be 0.75 mm .030 in. minimum for all socket sizes except for 12P which is used in a 1.27 mm .050 in. minimum thick pc board. Contact the Product Information number listed at the bottom of page 1 for suitability of other board materials or thicknesses. B. PCBoardHoleDimensions The socket holes in the pc board must be precisely drilled to ensure proper placement and optimum performance of the socket. The drilled holes must be on 2.54 mm .100 in. centerlines (minimum). The dimensions provided in Figure 2 must be observed when preparing a pc board for AUGAT HOLTITE Sockets. 2 of 7 Rev B