TAT-125 Flexible, adhesive-lined, polyolefin heat-shrinkable tubing TAT-125 is an adhesive-lined, flexible, must withstand flexing or other application to form a positive thin-wall, heat-shrinkable tubing. physical abuse. Because both tubing environmental seal. The adhesive It provides one-step electrical and adhesive are flexible, the will adhere to a wide variety of insulation and moisture sealing for moisture seal is resistant to bending plastics, rubbers, and metals, a wide variety of applications. of the substrate. including PVC, polyethylene, neoprene, lead, and steel. TAT-125 is especially suitable for The thin adhesive lining of TAT-125 applications where the moisture seal melts and flows with the heat of Temperature rating Full recovery temperature: 121C Continuous operating temperature: 55C to 110C Specifications* Type Raychem Military UL TAT-125 Type 1 (colors) RW-3032 AMS-DTL-23053/4, Cl. 2 E85381 TAT-125 Type 2 (clear) RW-3032 *When ordering, always specify latest issue. Dimensions (millimeters/inches) W W1 Expanded as supplied Fully recovered after heating D d Inside diameter Recovered wall thickness** D(min.) d (max.) W W1 Expanded Recovered Nominal Nominal Size as supplied after heating total wall adhesive wall 1/8 3.2 0.125 1.6 0.062 0.68 0.027 0.23 0.009 3/16 4.7 0.187 2.4 0.093 0.71 0.028 0.25 0.010 1/4 6.4 0.250 3.2 0.125 0.74 0.029 0.13 0.005 3/8 9.5 0.375 4.7 0.187 0.74 0.029 0.13 0.005 1/2 12.7 0.500 6.4 0.250 0.76 0.030 0.15 0.006 3/4 19.1 0.750 9.5 0.375 0.89 0.035 0.15 0.006 1 25.4 1.000 12.7 0.500 1.07 0.042 0.20 0.008 11/2 38.1 1.500 19.1 0.750 1.19 0.047 0.28 0.012 2 50.8 2.000 25.4 1.000 1.65 0.065 0.56 0.022 3 76.2 3.000 38.1 1.500 1.65 0.065 0.56 0.022 4 4.000 50.8 2.000 1.78 0.070 0.56 0.022 101.6 **Wall thickness will be less if tubing recovery is restricted during shrinkage. Ordering information Colors Standard Black Nonstandar White, r d ed, blue, yellow, green, orange, brown, violet, clear (non-flame-retardant jacket) Size selection Always order the largest size that will shrink snugly over the component being covered. Standard packaging 4-foot lengths Nonstandard sizes Sizes of 2 inches and larger are by special order only. Other nonstandard sizes are available upon special request. Ordering description Specify product name, size, and color for example, TAT-125 1/4-0 (0=Black).Specification values Property Unit Requirement Method of test PhysicalDimensions mm (inches) See reverse ASTM D 2671 Longitudinal change* percent +0, 5 maximum ASTM D 2671 Tensile strength psi 1500 minimum ASTM D 2671 Ultimate elongation percent 200 minimum ASTM D 2671 4 S m ecant modulus (as supplied) psi 2.5 x 10 aximum ASTM D 2671 Cold impact No cracking AMS-DTL-23053 (at 55C/67F) Heat shock No dripping, flowing, AMS-DTL-23053 (4 hours at 250C/482F) or cracking of outer wall Heat resistance No dripping, flowing, AMS-DTL-23053 (168 hours at 175C/347F) or cracking of outer wall Color Pass MIL-STD 104 Color stability Pass MIL-STD 104 (24 hours at 175C/347F) Electrical Dielectric strength volts/mil ASTM D 2671 Sizes 1/8 through 1 500 minimum Sizes 1 1/2 and larger 400 minimum 12 Volume resistivity ohm-cm 1 X 10 minimum ASTM D 2671 Chemical Copper corrosion No corrosion ASTM D 2671 (16 hours at 121C/250F) Procedures A & B Flame retardancy** Self-extinguishing within AMS-DTL-23053 1 minute, 25% maximum Test A flag burn Fungus resistance Rating of 1 or less ASTM G21 Water absorption percent 0.5 maximum ASTM D 2671 (24 hours at 23C/73F) Fluid resistance AMS-DTL-23053 (24 hours at 24C/75F) in: Hydraulic fluid (MIL-H-5606) JP-8 fuel (MIL-T-5624) Lubricating oil (MIL-L-7808 and MIL-I-23699) Salt water, 5% (O-S-1926) De-icing fluid (MIL-A-8243) Followed by tests for: Tensile strength psi 1000 minimum ASTM D 2671 Dielectric strength volts/mil ASTM D 2671 Sizes 1/8 through 1 400 minimum Sizes 1 1/2 and larger 300 minimum Note: Except for dimensions and longitudinal change, specification values apply to outer jacket only. *Sizes and colors not included in AMS-DTL-23053/4, Class 2 have a longitudinal change requirement of +0, -10 maximum. **Only the outer jacket of TAT-125 is flame-retardant the outer jacket of clear TAT-125, however, is not flame-retardant. Typical properties Adhesive Peel strength T-PEEL, 2/minute Polyethylene 15 lb./in. width Neoprene 10 lb./in. width PVC 10 lb./in. width Lead 5 lb./in. width Steel 15 lb./in. width Raychem is a trademark of Tyco Electronics Corporation. Users should independently evaluate the suitability of the product for their application. Tyco Electronics Corporation 300 Constitution Drive Faraday Road 3816 Noborito, Tama-ku Asia Pacific Headquarters Menlo Park, CA 94025-1164 Dorcan, Swindon, SN3 5HH Kawasaki, Kanagawa 214-8533 26 Ang Mo Kio, Industrial Park 2 USA United Kingdom Japan Singapore 569507 Tel:(800) 926-2425 (US & Canada) Tel: +44 1793 528171 Tel: +81 44 900 5102 Tel: +65 4866 151 Tel:+1 (650) 361-3860 (All other countries) All information, including illustrations, is believed to be reliable. Users, however, should independently evaluate the suitability of each product for their application. Tyco Electronics Corporation makes no warranties as to the accuracy or completeness of the information, and disclaims any liability regarding its use. Tyco Electronics Corporations only obligations are those in the Standard Terms and Conditions of Sale for these products and in no case will Tyco Electronics Corporation be liable for any incidental, indirect, or consequential damages arising from the sale, resale, use, or misuse of the product. Tyco Electronics Corporations Specifications are subject to change without notice. In addition, Tyco Electronics Corporation reserves the right to make changes in materials or processing without notification to the Buyer which do not affect compliance with any applicable specification. For more information about this product visit www.tycoelectronics.com 1994, 2002 Tyco Electronics Corporation Printed in USA 1654047 Rev. 9/05