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igure 1 This instruction sheet provides application and maintenance procedures for Hand Tool Frame Assembly 58532 , 58555 , and 58588 . The tool is designed to accept interchangeable crimping die assemblies for crimping various types of connectors. Reasons for reissue are provided in Section 7, REVISION SUMMARY. In most cases, the hand tool frame assembly is provided with a specific set of dies and is considered a component part of a crimping assembly. Refer to .,:7* the appropriate instruction sheet packaged with the The hand tool consists of two crimping jaws, an hand tool/crimping die assembly, or with the separate adjustable ratchet, springactuated handles, two die die assembly, for information regarding crimping retaining screws, and an emergency ratchet release. procedures, crimp height inspection, and crimping die The slotted design of the crimping jaws permits easy gaging. installation and removal of crimping dies. The Read these instructions thoroughly before installing adjustable ratchet allows handle pressure to be set dies and using the tool. for optimum crimping die performance. -.8(4397411*))4(:2*39.88:/*(994(-&3,* >(4 1*(9743.(8 47547&9.43 &77.8:7, 4+ 11 39*73&9.43&1 .,-98 *8*7 *) 471&9*897* .8.43&3) *,.43&1 :8942*7 *7 .(* 14,4&3) >(4 1*(9743.(8&7*97&)*2&708 .8.94:7<*8.9*&9--- ,) &,*)(+) 7&)*2&70 9-*7574):(98 14,48 &3)(425&3>3&2*8:8*)&7*9-*5745*79>4+9-*.77*85*(9. *4<3*78 ((% ) *& %* 5. To remove the die assembly, close the tool handles until the ratchet releases, and allow the Select the desired die assembly, remove the die handles to open fully. Loosen and remove the die retention screws from the tool jaws, and proceed as retention screws and slide the dies out of the tool follows: jaws. * (+% * 1. Install the wire and insulation anvil dies, with the 1. Place the upper die in the stationary jaw of the chamfers facing the front of the tool, and with the tool frame. die markings facing outward, into the movable jaw of the frame assembly. 2. Insert the die retaining pins and the short die retention screw. Do not tighten the screw completely. 3. Install the wire and insulation crimper dies, with the chamfers facing the front of the tool, and with the die markings facing outward, into the stationary jaw of the frame assembly. 4. Insert the die retaining pins and the long die retention screw. Do not tighten the screw completely. ( Figure 2 % 2. Insert a die retention screw through the jaw and die and tighten the screw so that the die is held in place, but do not tighten the screw completely at this point. & ( 3. Place the lower die in the moving jaw of the tool frame. Install a die retention screw through the jaw and die and tighten the screw so that the die is held in place, but do not tighten the screw Figure 3 completely at this point. 5. Slowly close the tool handles, allowing the dies to mate and/or align. Continue closing the tool handles until the ratchet makes the fourth click, then tighten both die retention screws until snug. 6. Install the locator assembly and tighten the hex 4. Slowly close the tool handles, allowing the dies nut. to mate and/or align. Continue closing the tool handles until the ratchet makes the fourth click, 7. Reverse the procedure to remove the die then tighten both die retention screws until snug. assembly. ) &