108-1979 Product 11Mar11 Rev B Specification AUGAT* HOLTITE* Sockets 1. SCOPE 1.1. Content This specification covers performance, tests and quality requirements for the TE Connectivity (TE) AUGAT* HOLTITE* Sockets. These sockets are designed to be press-fit into a plated through hole of a printed circuit board. This unique design allows the plated through hole to become a component socket. The sockets are designed to accept a .016 to .021 inch round lead (5P), .011 X .018 inch rectangular lead (5P), .020 to .030 inch round lead (6P), .025 to .035 inch round lead (8P) and .035 to .045 inch round lead (12P). 1.2. Qualification When tests are performed on the subject product line, procedures specified in Figure 1 shall be used. All inspections shall be performed using the applicable inspection plan and product drawing. 1.3. Qualification Test Results Successful qualification testing on the subject product line has been completed. The Qualification Test Report number for this testing is 501-500. This documentation is on file at and available from Engineering Practices and Standards (EPS). 2. APPLICABLE DOCUMENTS The following documents form a part of this specification to the extent specified herein. Unless otherwise specified, the latest edition of the document applies. In the event of conflict between the requirements of this specification and the product drawing, the product drawing shall take precedence. In the event of conflict between the requirements of this specification and the referenced documents, this specification shall take precedence. 2.1. TE Documents 109-197: TE Test Specifications vs EIA and IEC Test Methods 501-500: Qualification Test Report 2.2. Commercial Standard EIA-364: Electrical Connector/Socket Test Procedures Including Environmental Classifications 3. REQUIREMENTS 3.1. Design and Construction Product shall be of the design, construction and physical dimensions specified on the applicable product drawing. 3.2. Materials Materials used in the construction of this product shall be as specified on the applicable product drawing. 2011 Tyco Electronics Corporation, Indicates change For latest revision, visit our website at www.te.com/documents. 1 of 5 a TE Connectivity Ltd. Company *Trademark For Regional Customer Service, visit our website at www.te.com All Rights Reserved TE logo is a trademark. Other products, logos, and company names might be trademarks of their respective owners. LOC B108-1979 3.3. Ratings Current: 5 amperes using an .062 inch thick glass epoxy, Type FR4, with 2 ounce copper, plated, with electroplated (.001 inch minimum) copper and electroplated tin/lead (.0003 inch minimum) plated through holes. Temperature: Gold contacts: -55 to 125C Tin/lead contacts: -55 to 105C 3.4. Performance and Test Description Product is designed to meet the electrical, mechanical and environmental performance requirements specified in Figure 1. Unless otherwise specified, all tests shall be performed at ambient environmental conditions per EIA-364. 3.5. Test Requirements and Procedures Summary Test Description Requirement Procedure Examination of product. Meets visual requirements. EIA-364-18. Visual inspection. ELECTRICAL Low level contact resistance. 10 milliohms maximum initial for EIA-364-23. recessed contacts Subject specimens to 100 11 milliohms maximum initial for milliamperes maximum and 20 flush contacts. millivolts maximum open circuit 15 milliohms maximum final. voltage. See Figure 3. Insulation resistance. 1,000 megohms minimum. EIA-364-21. Test between adjacent contacts on .100 inch centerlines. Temperature rise vs current. 30EC maximum temperature rise at EIA-364-70, specified current. Method 1. Stabilize at a single current level until 3 readings at 5 minute intervals are within 1EC. MECHANICAL Vibration, sinusoidal. No discontinuities of 1 microsecond EIA-364-28, or longer duration. Test Condition IV. See Note. Subject mated specimens to 10- 2000-10 Hz traversed in 20 minutes with 1.5 mm .06 in maximum total excursion or 20 Gs, whichever is less. 4 hours in each of 3 mutually perpendicular planes. Durability. See Note. EIA-364-9. Insert and withdraw a .020 inch diameter polished steel test pin 50 times at a maximum rate of 500 cycles per hour. Figure 1 (continued) Rev B 2 of 5