6368062-8 TE Connectivity

8 7 6 5 4 3 2 1 THIS DRAWING IS UNPUBLISHED. RELEASED FOR PUBLICATION 20 LOC DIST REVISIONS ALL RIGHTS RESERVED. COPYRIGHT 20 BY - C P LTR DESCRIPTION DATE DWN APVD AA 22 C4 ECR-12-003298 13FEB2012 JJ AC 59.82 31.06 D REV PER ECR-13-009307 8JUN2013 D.Z S.H 8 E ECO-15-006810 29DEC2015 LL SH LED 2 PANEL GROUND 1.22 REF 1. MATERIAL: SHIELD TYP HOUSING 8 HOUSING PBT POLYESTER, BLACK, UL 94V-O. LED 3 TERMINALS TYP 18.39 0.33 THICK PHOSPHOR BRONZE PLATED WITH 1.27m MINIMUM THICK HARD GOLD IN LOCALIZED AREA AND 3.81m MINIMUM THICK MATTE TIN IN ACTION PIN COMPLIANT PIN TERMINAL AREA OVER 1.27m MINIMUM THICK NICKEL UNDERPLATE. 7 SHIELD TYP 0.25 THICK COPPER ALLOY PLATED WITH 2.03m MINIMUM BRIGHT TIN D D OVER 1.27 m MINIMUM NICKEL LIGHT EMITTING DIODE (LED) DIFFUSED EPOXY LENS, 12.95 CARBON STEEL WIREFRAME LEADS 22.99 PREPLATED WITH 8.89 m THICK Sn/Cu OVER 2.03 m THICK Ag OVER 0.43 1.02 m THICK Cu OVER 3.56 m THICK Ni OVER 1.02 m THICK Cu UNDERPLATE LED ACTION PIN - COMPLIANT PIN CONTACTS 0.3 THICK BRASS PLATED WITH 2um MINIMUM MATTE TIN OVER 1.27um MINIMUM NICKEL UNDERPLATE. 5.71 2. JACK CAVITY CONFORMS TO FCC RULES AND REGULATIONS, PART 68 SUBPART F. 8 ACTION PIN- 3. ALL DIMENSIONS ARE NOMINAL UNLESS OTHERWISE SPECIFIED. 10 8 SHIELD SURFACE COMPLIANT PIN LED 4 4 LED 1 DRILLED HOLE DIA = 1.02.025. TERMINAL TYP PC BOARD TYP COPPER THICKNESS = 0.025-0.075. REF TIN LEAD THICKNESS = 0.008 MIN. GROUND CLIP P/N 6368062-2 SHOWN 5 DATUMS AND BASIC DIMENSIONS ESTABLISHED BY CUSTOMER. QUANTITY: 4 FOR -2, -4, -5 & -6 ONLY 6 DATE CODE LOCATED ON REAR OF PART APPROXIMATELY AS SHOWN. PANEL SHOWN IN THIS 6 7 CONTACTS ARE NOT INTENDED TO BE ALIGNED WITH EACH OTHER. VIEW FOR CLARITY C C 8 SUGGESTED OPERATING CURRENT FOR LEDS IS 20 mA. 1.78 0.61 9. TWO LEDS PER PORT, SIZE .079 X .118, SEE TABLE FOR COLOR RECOMMENDED PANEL LOCATION 10 CLEAR 0.038 MIN THICK SURFACE PROTECTION TAPE APPLIED TO SHIELD SURFACE. FILM DOES NOT HAVE CUTOUTS IN EACH PORT. D/C 0015 REMOVE TAPE PRIOR TO MATING A MODULAR PLUG TO THE JACK 14.61 11 MATERIAL: TYP SHIELD YELLOW GREEN 0.25 THICK COPPER ALLOY PLATED WITH 1.27 m MINIMUM SATIN NICKEL. 2.42 REF 12 THE PART NUMBER 6368062-7 IS PRELIMINARY. 13 ONLY FOR 6368062-8 CONTACT AREA LUBRICATED WITH BELLCORE APPROVED LUBRICANT TECHNICAL REFERENCE GR-1217-CORE ANODE (+) ANODE (+) ISSUE 1, NOVEMBER 1995. 14 THE PART 6368062-9 IS ONLY FOR CUSTOMER ZYNX SPECIAL LED LUMINOUS INTENSITY REQUEST.( GREEN:13~20 mcd GREEN RED YELLOW:6~9 mcd.) LED CURRENT DIAGRAM PARTIAL BACK VIEW LED CIRCUIT DIAGRAM B B 6368062-4,-7 6368062-6 YELLOW YELLOW GREEN GREEN WITHOUT GROUND CLIP 1-6368062-6 11 YELLOW YELLOW GREEN GREEN WITHOUT GROUND CLIP 6368062-9 14 GREEN GREEN GREEN GREEN WITHOUT GROUND CLIP 6368062-8 13 - N/A N/A GREEN/YELLOW GREEN/YELLOW WITHOUT GROUND CLIP 6368062-7 12 - RED/GREEN RED/GREEN RED/GREEN RED/GREEN WITH GROUND CLIP 6368062-6 GREEN GREEN GREEN GREEN WITH GROUND CLIP 6368062-5 10 - GREEN/YELLOW GREEN/YELLOW GREEN/YELLOW GREEN/YELLOW WITH GROUND CLIP 6368062-4 - YELLOW YELLOW GREEN GREEN WITHOUT GROUND CLIP 6368062-3 - GREEN GREEN GREEN GREEN WITH GROUND CLIP 6368062-2 - GREEN GREEN GREEN GREEN WITHOUT GROUND CLIP 6368062-1 LED 4 LED 3 LED 2 LED 1 DESCRIPTION PART NUMBER REMARKS A A (LOWER-RIGHT) (UPPER-RIGHT) (UPPER-LEFT) (LOWER-LEFT) DWN 15APR2005 THIS DRAWING IS A CONTROLLED DOCUMENT. L.A.MAYER TE Connectivity CHK 15APR2005 J.WESTMAN DIMENSIONS: TOLERANCES UNLESS APVD NAME OTHERWISE SPECIFIED: 15APR2005 PN 6368062-7 S.FLICKINGER mm STACKED MODULAR JACK ASSEMBLY, PRODUCT SPEC 0 PLC - PN 6368062-1,-2,-3,-4,-5,-6,-8 2x4 OFFSET, WITH LEDS, 8 POSN, RJ45 SCALE 2:1 1 PLC 0.13 108-1854 2 PLC 0.13 SHIELDED, PANEL GROUNDS, CAT 5 AND 1-6368062-6 3 PLC APPLICATION SPEC - 4 PLC - SIZE CAGE CODE DRAWING NO RESTRICTED TO SCALE 2:1 ANGLES 114-2160 1 MATERIAL FINISH WEIGHT 00779 6368062 - - A1 - - SCALE SHEET OF REV Customer Drawing 4:1 1 2 E 4805 (3/11)8 7 6 5 4 3 2 1 THIS DRAWING IS UNPUBLISHED. RELEASED FOR PUBLICATION 20 LOC DIST REVISIONS ALL RIGHTS RESERVED. COPYRIGHT 20 BY - C P LTR DESCRIPTION DATE DWN APVD AA 22 - SEE SHEET 1 - - - 60.71 D D PC BOARD 23.88 REF 6.18 REF TOP OF PC BOARD RECOMMENDED PANEL CUT-OUT C 2.8 C 5 1 -X- 5 X.XX 54.24 5.34 43.82 4 0.89 0.06 29.21 1.02 1.13 TYP PLATED THROUGH HOLES 4 14.61 TYP 0.89 0.06 0.89 0.06 2.03 DETAIL B 14.61 TYP PLATED PADS REQUIRED FOR 6368062-2, -4, -5 & -6 3 PLC PLATED THROUGH HOLES TYP (PRODUCT WITH GROUNDING CLIPS) 4 PLC PIN 8 LED 3 SCALE 10:1 REF TYP TYP 4 PLACES B B 4.76 1.62 TYP 5.33 TYP 2.54 2 PLC 2 PLC 4.06 TYP 1 8 8 LED 2 2.54 2.54 TYP 1 TYP TYP 5 -Y- 3.81 PIN 1 LED 1 2 PLC REF TYP 2.73 SEE DETAIL B ANODE TYP TYP TYP CATHODE 2.54 2.03 TYP 15.88 WITH GROUNDING CLIPS TYP TYP 2.54 A A TYP 14.61 16.13 WITHOUT GROUNDING CLIPS DWN 15APR2005 THIS DRAWING IS A CONTROLLED DOCUMENT. L.A.MAYER LED 4 TE Connectivity TYP CHK 15APR2005 J.WESTMAN DIMENSIONS: TOLERANCES UNLESS TYP APVD NAME OTHERWISE SPECIFIED: 15APR2005 S.FLICKINGER mm STACKED MODULAR JACK ASSEMBLY, PRODUCT SPEC 0 PLC - PC BOARD LAYOUT 2x4 OFFSET, WITH LEDS, 8 POSN, RJ45 1 PLC 0.13 108-1854 2 PLC 0.13 SHIELDED, PANEL GROUNDS, CAT 5 3 PLC APPLICATION SPEC PARTS WITH GROUNDING CLIPS = 1.65 - 4 PLC - SIZE CAGE CODE DRAWING NO RESTRICTED TO (COMPONENT SIDE) ANGLES 114-2160 1 PARTS WITHOUT GROUNDING CLIPS = 1.91 MATERIAL FINISH WEIGHT 00779 6368062 - - A1 LED 3, 4 NOT REQUIRED FOR 6368062-7 - - SCALE SHEET OF REV Customer Drawing 4:1 2 2 E 4805 (3/11)