59:8 *:065 /,,: % )) ) &( (% ) % ,< ,9: 6 5:05. *8,=,:(0505. 5+,5:,805. 6+,3 6+,3 6+,3 6+,3 (*/05, ,8405(:05.,8405(:05. (*/05, (*/05, ,8405(:05.,8405(:05.%50:%50: ,8405(:05.,8405(:05. (*/05, (*/05, ,8405(:05.,8405(:05. (*/05, (*/05, & & 9:64,84(5 (39/6=5057(8,5:/,909 65:(*: 66305. 9909:(5*, ,5:,8(::/,5 4),8(::/,)6::646-:/097(.,-68468,05-684(:065 6+,3 ,8405(:05. (*/05, /(9),,59 7,89,+,+) 6+,3 ,8405(:05. (*/05, -685,=(7730*(:0659 68,>09:05.(7730*(:0659 :/, 6+,3 *(59:033), 9,+ Figure 1 Crimping Die Assemblies listed in Figure 1 are designed for use in the terminal applicators contained in the power units listed. Each die assembly, when Reasons for reissue of this instruction sheet are installed in the terminal applicator, crimps provided in Section 6, REVISION SUMMARY. SOLISTRAND terminals onto the appropriate wire size listed in Figure 2. Each die assembly features a nest die and indenter These instructions provide specific information die with mounting screws and retaining rings for regarding the die assemblies and applicable securing the dies to the applicator. terminals. For information regarding operation of the power unit, refer to the applicable customer manual. Read these instructions and any referenced instructions thoroughly before using the dies. /09*65:8633,++6* 4,5:099 )1,*::6*/(5., *6 3,*:8650*9 68768(:065 (8809) 8. 6- 33 5:,85(:065(3 0./:9 ,9,8<,+ % 683(:,9:8,<09065(5,.065(3 9:64,8 ,8<0*, 36.6(5+ *6 3,*:8650*9(8,:8(+,4(829 <090:6 8=,)90:,(: +++ *, & *(& ) & 8(+,4(82 :/,8786+ *:9 36.69 (5+*647(5 5(4,9 9,+(8,:/,7867,8: 6-:/,088,97,*:0<,6=5,89 -),*& .. ) ( .%+- -)(. /7+ 97/6 +4-9. +/ 579+73/428+2+)9/54/4,5739/54 7+,+795 925- For die installation, machine setup, and machine operation, refer to the instructions packaged with the machine. Use the appropriate wire size and strip length according to Figure 2. Inspect crimped terminals according to Figure 3. Use only the terminals that meet the conditions shown in % & the ACCEPT column. REJECT terminals can be avoided by following the above procedures and by performing regular die maintenance, as provided in % & Section 4, MAINTENANCE AND INSPECTION. % & It is recommended that a maintenance and inspection % & program be performed periodically to ensure Figure 2 dependable and uniform terminations. /4-2+ 4*+49 7/36 /7+ / + 42> /4-2+ 4*+49 7/36 /7+ / + 42> /7+ / + 4-+ 936+* +7+ /7+ / + 4-+ 936+* +7+ 7/36459)+49+7+*54</7+(77+2 +,+795+73/42 4 :9 *0:893+49 /4662/)(2+):8953+734:2 /7+8/ +(+/4-:8+**5+845939).</7+74-+ 8936+*549+73/424**/+ 7/36)+49+7+*54</7+(77+2 7/3683>(+5,,)+49+7 /7+459,:22>/48+79+*57<754-897/62+4-9. +,+795 97/6 +4-9. *0:893+49 7+88 /3/4- 57 /7+ *0:893+49 4 :9 /4662/)(2+):8953+734:2 /7+8/ +(+/4-:8+*39).+8</7+8/ +74-+8936+* 549+73/424**/+ /)1+*573/88/4-</7+)54*:)9578974*8 +,+795 97/6 +69. *0:893+49 /4662/)(2+):8953+734:2 /7+,:22>/48+79+*4*/48:29/54*5+8459+49+79+73/42 =)+88/ + ,28. 549+73/42/4*/)9+8<754-*/+8 </7+ </7+(77+2 579+73/42)53(/49/5457*3-+**/+8 /7+/8,2:8.</9.57+=9+4*882/-.92>(+>54*+4*5, +/ ,</7+/48:29/54+49+78</7+(77+25,9+73/42 9.+</7+ 9+73/42</7+(77+2 <8/48+79+*955,757<754-897/62+4-9.<8:8+* +,+795 /7+ *0:893+49 4 :9 57 97/6 +4-9. *0:893+49 /4662/)(2+):8953+734:2 Figure 3 5, >)5 2+)9754/)8 576579/54 +