6EL1SC TE Connectivity

Series L Power Entry Modules with RFI Power Line Filter for General or Medical Applications UL Recognized CSA Certified EDL4C/EHL4C VDE Approved EDL1S/EHL1S L Series The L series power entry modules are compact units that Electrical Schematics combine a multi-function power entry module and high DL Models (with switch) performance RFI filtering capabilities. They are available with either a four-voltage selector or a DPST on/off switch. Both variations can be specified with North American or Note 1 2 1 European fusing capabilities and are available in either Note 2 flange or snap-in mounting. 4 3 These filters are UL recognized, CSA certified, and VDE approved. The L series modules offer a choice of filters for general or medical applications. EDL ModelsThe RFI filter is for general purpose DL Models (with 4-voltage selection) applications where line-to-line and line-to-ground noise must be controlled. The filter is designed to meet the very low leakage requirements of VDE portable equipment. They are available in three current ratings. EHL ModelsThis medical filter provides susceptibility protection without the leakage current associated with line- to-ground capacitors. Designed to allow equipment to Note 1 meet UL544 for patient care and nonpatient care equipment, the EHL filter has a maximum leakage current HL Models (with switch) of 2 A at 120 VAC 60 Hz. See Appendix C for more information on medical applications and UL standards. Note 1 2 1 Voltage Selection Note 2 4 3 HL Models (with 4-voltage selection) L 99 Note 1 To change selected voltage: disconnect the power cord open cover using a small blade screwdriver or similar tool insert the tool into the voltage selection slot and remove Resistor location for reference only. wheel from unit select desired voltage replace wheel into NOTES: Note 1: Provision for dual European style fusing. unit and close cover, making sure the selected voltage Note 2: On/Off switch present only with S suffix. appears in connector window. Libertyville, IL (847) 680-7400 - www.cor.comL Series Specifications Filtered Case Dimensions - Filtered Metric shown in italics. Maximum leakage current, each line-to-ground: 120 VAC 60 Hz: EDL Models 0.25 mA Part No. A B C D E F +.008/-.00 +.008/-.00 .015 EHL Models 2 A (max) (max) (max) +.203/-.00 +.203/-.00 .038 250 VAC 50 Hz: EDL Models 0.50 mA Flange 1.98 2.01 2.30 1.122 2.201 1.575 EHL Models 5 A Filtered 50.3 51.1 58.4 28.50 55.91 40.00 Hipot rating (one minute): Snap-in 1.28 2.01 2.30 1.122* 2.201 line-to-ground EDL Models 1500 VAC Filtered 32.5 51.1 58.4 28.50 55.91 EHL Models 1500 VAC For panel thickness of .031 - .079 (0.8 - 2.0). For panel thickness line-to-line All Models 1450 VDC of .083 - .114 (2.1 - 2.9) use 2.213 (56.21). Operating voltages: * For snap-in application, the D sides of the cutout must have a 1S & 1SC Models - Fixed 100, 120, 220, 240 VAC .02 (.508) radius on the installation side. 4 & 4C Models Selectable 100, 120, 220, 240 VAC Operating frequency: 50/60 Hz Case Styles - Filtered Rated voltage: 120/250 VAC Flange Models Switch: Rated for 10,000 (1S & 1SC models only) operations at full load 51 Amp inrush capability Fuse (not included): Accepts one 1/4 x 1-1/4 fuse or two 5 x 20mm fuses Terminals: .110 (2.79) terminals except for switch. Switch terminals .187 (4.8). Minimum insertion loss in dB: Line-to-ground in 50 ohm circuit Current Frequency-MHz Rating .05 .15 1 5 10 30 Snap-In Models EDL Models 2A 6 14 24 40 45 50 4A 2 8 18 32 38 45 6A 1 6 17 31 37 45 EHL Models 6A 3 8 15 18 18 18 Line-to-line in 50 ohm circuit Current Frequency-MHz Rating .05 .15 1 3 5 10 30 Metric fuse models have additional jumper from filter to module Note: Snap-in models allow front mounting only. EDL Models 2A 7 16 21 23 37 47 50 Recommended Panel Cutout 4A 6 15 18 23 26 45 47 6A 6 15 20 25 25 45 50 EHL Models 6A 4 14 20 28 32 38 42 L 100 www.cor.com - Libertyville, IL (847) 680-7400