SPECIFICATION CONTROL DRAWING 7024E1664 Date 6-14-11 70 OHM, AWG 24, 19 STRANDS OF AWG 36, TWINAXIAL CABLE CHEMINAX Revision A THIS SPECIFICATION SHEET FORMS A PART OF THE LATEST ISSUE OF RAYCHEM SPECIFICATION 1200. CONSTRUCTION DETAILS ELECTRICAL CHARACTERISTICS DIMENSIONS ARE NOMINAL VALUES IN INCHES UNLESS OTHERWISE DESIGNATED. CHARACTERISTIC IMPEDANCE 70 5 ohms, Method C at 1 MHz CONDUCTORS MUTUAL CAPACITANCE 30.0 pF/ft. (maximum) AWG 24, 19 Strands of ATTENUATION 1.0 dB/100 ft. (nominal) at 1 MHz AWG 36, Silver-Coated .0250 High-Strength Copper 1.4 dB/100 ft. (maximum) at 1 MHz Alloy DIELECTRICS .047 Radiation-Crosslinked, ADDITIONAL REQUIREMENTS .002 Modified ETFE COMPONENT WIRE PRIOR TO CABLING (Test procedures per SAE AS22759) Colors - Light Blue/White CROSSLINKING PROOF TEST 300 3C for 1 hour, .625 inch mandrel, .375 lb., 2.5 kV dielectric test INSULATION (DIELECTRIC) ELONGATION 50% (minimum) 2 TENSILE STRENGTH 5000 lbf/in (minimum) INSULATION FLAWS SPARK TEST 3.0 kV (rms) IMPULSE TEST 8.0 kV (peak) INSULATION RESISTANCE 5000 megohms for 1000 ft. (minimum) SHIELD LOW TEMPERATURE-COLD BEND -65 3C for 4 hours, .500 inch mandrel, .111 AWG 38 1.00 lb., 2.5 kV dielectric test Silver-Coated Copper SHRINKAGE 200 3C for 1 hour, .125 inch (maximum) in 12 inches FINISHED CABLE (Test procedures per NEMA WC 27500, unless otherwise specified) BLOCKING 200C for 6 hours CROSSLINKED VERIFICATION 300 5C for 6 hours, 3.00 inch mandrel FLAMMABILITY 3 seconds (maximum) 3 inches (maximum) JACKET (Method B of Spec 1200) no flaming of facial tissue .123 Radiation-Crosslinked, JACKET (nominal) Modified ETFE ELONGATION 50% (minimum) .129 2 TENSILE STRENGTH 5000 lbf/in (minimum) (maximum) JACKET FLAWS SPARK TEST 1.0 kV (rms) IMPULSE TEST 6.0 kV (peak) JACKET THICKNESS .006 inch (nominal) LOW TEMPERATURE-COLD BEND -55 5C for 4 hours, 3.00 inch mandrel SHIELD COVERAGE 90% (minimum) VOLTAGE WITHSTAND 1500 volts (rms) (DIELECTRIC) Outer jacket color will be white (designated by a -9 appended to the part number, e.g. 7024E1664-9) unless otherwise specified. Designate outer jacket color with a dash number in accordance with MIL-STD-681. Other codes and suffixes may be added to the part number, as necessary, to capture any additional WEIGHT 12.5 lbs/1000 ft. (maximum) requirements imposed by the purchase order. Users should evaluate the suitability of this product for their application. Specifications are subject to change without notice. Tyco Electronics Corporation also reserves the right to make changes in materials or processing, which do not affect compliance with any specification, without notification to Buyer . Page 1 of 1 Raychem, TE Connectivity, TE connectivity (logo) and TE (logo) are trademarks. Raychem Wire & Cable THIS SPECIFICATION SHEET TAKES PRECEDENCE OVER DOCUMENTS 501 Oakside Avenue REFERENCED HEREIN. REFERENCED DOCUMENTS SHALL BE OF THE Redwood City, California 94063-3800 ISSUE IN EFFECT ON DATE OF INVITATION FOR BID. 1-800-227-8816 Fax: 1-650-361-6297 2011 Tyco Electronics Corporation, All rights reserved.X-ON Electronics Largest Supplier of Electrical and Electronic Components Click to view similar products for Time Delay & Timing Relays category: Click to view products by TE Connectivity manufacturer: Other Similar products are found below : 7012GD 7012L10BN 7012L10DY1N 7012L10FN 7012L10HN 7012L26K 7012L8AI2LLSN 7012L8BN 7012L8KN 7012OBILM 7012OIT 7012PALL 7012PDM 7012PFX 7022L10DN 7022L8BN 7022L8EN 7022L8HN 7022X3D 7024NB 7024SCT 88256455 H3BG- N8H AC110V H3CRF8AC2448DC1248 1423151-3 1423154-8 1423462-7 1423618-6 1423151-5 1423156-7 1423618-4 2112AH1SDC947 2122DH1NJC467 2122DH1PE 2-1617805-2 2-1617805-6 K61C-08 286XCXC-300-24D SCBRX022XXACXAC991 SHS10S110A SHS20M220A 1755074-5 SSC12AKA FAASPRING2 2112DH3NDC50-13 2122DH34NDC629 2-1437479-8 2-1617805-1 2-1617805-3 2- 1617805-7