CII Low Signal Relays
CII Low Signal Relays
Double Pole, Electrically Held, 2 Amps and Less (Continued)
Electrical Characteristics Operating Characteristics
.150 Grid-space Relays
Contact Ratings Operate Time 4 ms max.
Type 3SBC (2PDT) Standard
DC resistive 2 amps at 28 volts
Release Time 4 ms max.
1
(50,000 operations)
135 mW 2PDT
Contact Bounce 1.5 ms
1 Amp @ 28 V (100,000 operations)
50 mW (Form AB)
Dielectric Strength
DC inductive 0.5 amps at 28 volts,
1 PNC1 PNO
500 volts rms at sea level;
200 mH
350 volts rms at 70,000 feet and above
AC resistive 0.5 amps at 115 volts
Insulation Resistance 1,000
AC 0.125 amps at 115 volts (case
Product Facts
megohm min. over temperature range
grounded)
Low-level 50 A at 50 mV
n Low profile only
Environmental Characteristics
Peak AC or DC
0.32 inches high
Vibration 30G, to 3000 Hz
Contact Resistance
n Internal diode for coil Shock 100 G at 11 ms
0.050 ohms max.; 0.150 ohms after life
The .150 Grid-space relay
transient suppression and
Temperature -65C to +125C
test
only 0.32 inches high
transistor driven models
Life 100,000 operations at rated
See page 1-44 for Mounting Forms,
saves space in electronic
available
loads listed; 1,000,000 operations at Terminals and Circuit Diagrams.
packaging. The pin spacing
low-level loads
n Qualified to MIL-R-39016/13
allows you to insert the relay
with no intermediate pin
n RF designs available
spreaders as well as
meet applicable military
specifications.
*Values listed are factory test and inspection data. User should allow for meter variations.
At nominal resistance plus 10%. Applicable over the operating temperature range in circulating air.
See Page 1-42 for ordering instructions.
* The part number example shown on this page is for catalog items. For a list of specific QPL part numbers, please see the index in Section 15.
1-41
Catalog 5-1773450-5 Dimensions are shown for Dimensions are in millimeters USA: +1 800 522 6752 For additional support numbers
Revised 3-13 reference purposes only. unless otherwise specified. Asia Pacific: +86 0 400 820 6015 please visit www.te.com
Specifications subject UK: +44 800 267 666
www.te.com to change.CII Low Signal Relays
Double Pole, Electrically Held, 2 Amps and Less (Continued)
Electrical Characteristics Operating Characteristics
.150 Grid-space
Contact Ratings Operate Time 4 ms max.
Hybrid Relays
DC resistive 2 amps at 28 volts
Release Time 6 ms max.
Single Diode, Dual Diode
(50,000 operations)
Contact Bounce 1.5 ms
1 Amp @ 28 V (100,000 operations)
Type 3SBC (2PDT)
Dielectric Strength (Note 1)
DC inductive 0.5 amps at 28 volts,
500 volts rms at sea level;
135 mW 200 mH
350 volts rms at 70,000 feet and above
AC resistive 0.5 amps at 115 volts
Insulation Resistance (Note 1)
AC 0.125 amps at 115 volts (case
1,000 megohm min. over temperature
grounded)
Product Facts
range
Low-level 50 A at 50 mV
n Low profile only
Peak AC or DC
Environmental Characteristics
0.32 inches high
Contact Resistance
Vibration 30G, to 3000 Hz
0.050 ohms max.; 0.150 ohms after life
n 50 milliwatt forms available The hybrid .150 Grid-space
Shock 100 G at 11 ms
test
relay only 0.32 inches
n Qualified to MIL-R-39016/37 Temperature -65C to +125C
Life 100,000 operations at rated
high saves space in
loads listed; 1,000,000 operations at
n Qualified to MIL-R-39016/38 Semiconductor Characteristics
electronic packaging. The
low-level loads
at 25C
pin spacing allows you to
n RF designs available
Diode
insert the relay with no inter-
Max. Negative Transient 1.0 volt
mediate pin spreader.
Breakdown Voltage 100 VDC @ 10 A
Max. Leakage Current 1 A @ 50 VDC
See page 1-44 for Mounting Forms,
Terminals and Circuit Diagrams.
Note: Relays specified by catalog
Ordering Instructions
numbers (per above directions) are
Example: The relay selected in the
general use items controlled by cat-
example is a FORM AB .150-grid
alog specifications. Relays to be
relay, current calibrated, end
controlled by customer drawings
bracket mounting with 0.13-inch
or relays having requirements not
solder hook header, 210 ohms coil
covered in this publication will
resistance, and 50 mW sensitivity.
be assigned special catalog num-
By choosing the proper code for
bers upon request.
each of these relay characteristics,
the catalog number is
3SBC6131E2. The letter R following
sensitivity code indicates relay
received 5000 operation miss-test.
Ex. 3SBC6131E2R.
* The part number example shown on this page is for catalog items. For a list of specific QPL part numbers, please see the index in Section 15.
1-42
Catalog 5-1773450-5 Dimensions are shown for Dimensions are in millimeters USA: +1 800 522 6752 For additional support numbers
Revised 3-13 reference purposes only. unless otherwise specified. Asia Pacific: +86 0 400 820 6015 please visit www.te.com
Specifications subject UK: +44 800 267 666
www.te.com to change.