SPECIFICATION CONTROL DRAWING 55PC1141
Date
Revision
TITLE
FOUR CONDUCTOR CABLE, SHIELDED, JACKETED, GENERAL PURPOSE, 600 VOLT 2-21-08 B
This specification sheet forms a part of the latest issue of Raychem Specification 55PC.
JACKET - RADIATION-CROSSLINKED,
COMPONENT WIRES - 55PC0111
SHIELD - TIN-COATED COPPER
MODIFIED ETFE
CONSTRUCTION DETAILS
JACKET THICKNESS OUTSIDE DIAMETER WEIGHT
( in. ) ( in. ) ( lbs/1000 ft. )
CONDUCTOR SHIELD
PART NUMBER
SIZE SIZE
LOWER LOWER UPPER UPPER
1/
TARGET TARGET TARGET
(AWG) (AWG)
SPEC SPEC SPEC SPEC
WALL VALUE VALUE
LIMIT LIMIT LIMIT LIMIT
55PC1141-26-* 26 38 .0060 .0075 .098 .111 .124 10.86 11.38
55PC1141-24-* 24 38 .0060 .0080 .111 .125 .138 14.03 14.59
55PC1141-22-* 22 38 .0060 .0080 .123 .140 .156 18.57 19.19
55PC1141-20-* 20 38 .0060 .0080 .142 .161 .180 25.67 26.42
55PC1141-18-* 18 38 .0065 .0085 .163 .186 .209 36.10 37.15
55PC1141-16-* 16 38 .0065 .0085 .181 .205 .230 44.44 45.52
55PC1141-14-* 14 38 .0070 .0090 .213 .243 .273 64.85 66.35
55PC1141-12-* 12 38 .0075 .0095 .252 .296 .339 98.21 105.09
55PC1141-10-* 10 36 .0080 .0100 .285 .346 .407 152.70 157.77
Users should evaluate the suitability of this product for their application. Specifications are subject to change without notice.
Tyco Electronics also reserves the right to make changes in materials or processing, which do not affect compliance with any specification, without notification to Buyer.
1/ COLORS AND COLOR CODE DESIGNATORS SHALL BE IN ACCORDANCE WITH MIL-STD-681. HOWEVER, DUE TO LENGTH LIMITATIONS OF THE RAYCHEM PART NUMBER,
AN ALTERNATIVE COLOR CODE MAY REPLACE MIL-STD-681 COLOR CODE DESIGNATORS. (EXAMPLE: 901/902... MAY BE REPLACED BY Axxx.)
OTHER CODES AND SUFFIXES MAY BE ADDED TO THE PART NUMBER, AS NECESSARY, TO CAPTURE ANY ADDITIONAL REQUIREMENTS IMPOSED BY THE PURCHASE ORDER.
The TE logo, Tyco Electronics and Raychem are trademarks. Raychem Wire & Cable
501 Oakside Avenue
DIMENSIONS ARE IN INCHES, AND UNLESS OTHERWISE DESIGNATED ARE NOMINAL.
Redwood City, CA 94063-3800
Page 1 of 2
Phone: 1-800-227-8816
THIS SPECIFICATION SHEET TAKES PRECEDENCE OVER DOCUMENTS REFERENCED HEREIN.
Fax: 1-650-361-6297
REFERENCED DOCUMENTS SHALL BE OF THE ISSUE IN EFFECT ON DATE OF INVITATION FOR BID.
2008 Tyco Electronics Corporation. All rights reserved.SCD
Revision
Page 2 of 2 B
SPECIFICATION CONTROL DRAWING
55PC1141
CABLE RATINGS AND ADDITIONAL REQUIREMENTS
TEMPERATURE RATING: 150C
Maximum continuous conductor temperature
VOLTAGE RATING: 600 volts (rms) at sea level
CROSSLINK VERIFICATION: 300 3C for 1 hour
DIELECTRIC WITHSTAND: 1500 volts (rms), 60 Hz
JACKET COLOR: White preferred
JACKET ELONGATION AND TENSILE STRENGTH:
Elongation, 50% (minimum)
Tensile Strength, 5000 lbf/in (minimum)
JACKET FLAWS:
Spark Test, 1000 volts (rms)
Impulse Dielectric Test, 6.0 kV (peak)
SHIELD COVERAGE: 85% (minimum)
VOLTAGE WITHSTAND TEST (Post Environmental):
1000 volts (rms), 60 Hz, 1 minute
PART NUMBER:
The in the part numbers on page 1 shall be replaced by color code designators with
a slash separating the component wire colors and a dash separating the component
wire colors from the jacket color. Colors shown do not necessarily reflect the sequence
of manufacturing.
1/ Example: AWG 22, red, yellow, green and blue component wires; white jacket:
55PC1141-22-2/4/5/6-9
1/ See footer section on page 1