59:8 *:065 /,,: &33 *2.,/&4,0/ 33*.-6 *2.,/&4,/+ *&) *1&,2 ,43 % ,< 6478,99065 7805. ,- ,> ,(+ *8,=: % ,- ,*,7:(*3,9 % ,*,7:(*3,9 633 05 ,- % (+ 6 905. ,- 655,*:689 Figure 1 59,8:,8 ,- This instruction sheet covers the installation of MTA Terminating Head Repair Kits 856600 for repair of the terminating heads listed in Figure 1. Read these instructions thoroughly before using the repair kit. Refer to the instructions packaged with the MTA terminating head for setup and adjustment instructions. Reasons for reissue of this instruction sheet are provided in Section 5, REVISION SUMMARY. % %,8405(:05. Each repair kit is designed to replace all of the ,(+ ,- wearable parts in the terminating head. The items contained in the repair kit and their function are as +1 9:,8 ,- follows: Cam indexes the feed slide after each termination Locating pawl aligns the connector for insertion and retains it during termination Feed pawl (with compression spring) engages the connector and indexes it into position for termination A Feed slide automatically positions the connector A after each termination 6*(:05. A Drill blank helps to remove and install the roll pin in 6*(:05. A the locating pawl 0509/,+ ,,+ *2.,/&4,/+ *&) *1&,2 ,,+ 6478,99065 1. Remove the four hex head screws securing the housing to the terminating head. See Figure 2. 2. Depress the adjuster slightly, and pull the Figure 2 housing straight off the terminating head. % % % %/09*65:8633,++6* 4,5:099 )1,*::6*/(5., % *6 3,*:8650*9 68768(:065 (8809) 8. 6- 33 5:,85(:065(3 0./:9 ,9,8<,+ & % % 683(:,9:8,<09065(5+ ,.065(3 9:64,8 ,8<0*, % 36.6(5+% *6 3,*:8650*9(8,:8(+,4(829 <090:6 8=,)90:,(:555 46(0*-*(420/,(3 (0. %8(+,4(82 :/,8786+ *:9 36.69 (5+*647(5 5(4,9 9,+(8,:/,7867,8: 6-:/,088,97,*:0<,6=5,89 )&% +% ( %) %+* 3. Remove the feed slide (subassembly) from the housing. The repair kit should be stocked to prevent lost time when replacement of parts is necessary. Order replacement parts through your representative, or call 18005265142, or send a facsimile of your purchase order to 7179867605, or write to: CUSTOMER SERVICE (038035) 4. Using the drill blank, drive the roll pin past the TYCO ELECTRONICS CORPORATION feed pawl. Remove and discard the old feed pawl. PO BOX 3608 5. Install the new feed pawl. HARRISBURG PA 171053608 Terminating heads may be submitted for evaluation and repair. For customer repair service, call 18005265136. 6. Install the new feed slide (subassembly). Revisions to this instruction sheet include: 7. Rotate and depress the adjuster slightly to remove the cam. Inspect the condition of the Updated document to corporate requirements inserter. If the inserter is damaged or broken, it Added text to Section 2 must be replaced according to Section 4. The Corrected terminology in Steps 4 and 5 of inserter is not normally a wearing part and is not Section 3 contained in the repair kit. 8. Install the new cam, and rotate the adjuster. Make sure that the cam and the inserter are oriented as shown in Figure 2. 9. Install the housing into the terminating head as follows: a. Depress the adjuster slightly. b. Guide the inserter into the slot in the housing. c. Engage the feed slide into the opening in the cam. d. Place the housing on the terminating head and secure it with the four hex head screws.