Instruction Sheet PRO-CRIMPER*IIIHand CrimpingToolAssembly90760-1 408--9963 withDieAssembly90760-2 05 OCT 09 RevB PROPERUSEGUIDELINES CumulativeTraumaDisorderscanresultfromtheprolongeduseofmanuallypoweredhandtools.Handtoolsareintendedforoccasionaluseandlowvolume applications.Awideselectionofpoweredapplicationequipmentforextended--use,productionoperationsisavailable. Locator Assembly Stationary Jaw (Supplied with Die Assembly) Back of Tool (Wire Side) Front of Tool (Locator Side) Pivot Pin Die Assembly PRO--CRIMPER III Hand Crimping Tool Frame Moving Jaw 354940--1 (408--9930) Ratchet Adjustment Wheel ThePRO--CRIMPERIIIHandCrimpingTool isaCommercialgradetool and isdesignedprimarilyforfieldinstallation,repair,maintenancework,or Stationary prototypinginindustrial,commercial,orinstitutional applications.Product Handle crimpedwiththistool will meetthecrimpheightrequirementforhandtoolsin theappropriate114seriesspecification,butmaynotcomplywithotherfeature parametersofthespecification.TycoElectronicsoffersavarietyoftoolsto satisfyyourperformancerequirements.Foradditional information,contactthe Moving Handle Tooling Assistance Center at 1--800--722--1111. Wire TTEELLococaattoror CCoontantacctt TTEEDDiieeAAsssemsembbllyy Assembly Family Size(AWG) InsulDia StripLength 2.01 to 3.20 20--18 .079 to .126 33.20.20 ttoo 3.713.71 Mini Universal .126 to .146 2.49 to 3.20 90760--2 58516--1 MATE--N--LOK* 16 OR .098 -- .126 CCoonnectornnectorss ((22)) 33.50.50 ttoo 3.993.99 (2) .138 to .157 (2) 2.39 max (2) 20 (2) .094 max Suppliedwithdieassembly. Alsoavailableseparately. ContacttheTOOLING ASSISTANCE CENTER or PRODUCTINFORMATION (seebelow) for specific contactpartnumbers. Figure 1 Dimensions on this sheet are in millimeters with 1. INTRODUCTION NOTE inch equivalents provided in brackets . Figures PRO--CRIMPER III Hand Crimping Tool and illustrations are for identification only and are i Assembly 90760--1 consists of Die Assembly not drawn to scale. 90760--2 and PRO--CRIMPER III Hand Crimping Tool Frame 354940--1. The die assembly consists of crimping dies and a locator assembly. Read these Reasons for reissue are provided in Section 11, instructions thoroughly before crimping any contacts. REVISION SUMMARY. E2009 Tyco Electronics Corporation, Harrisburg, PA TOOLING ASSISTANCE CENTER1--800--722--1111 This controlled document is subject to change. 1 of 6 PRODUCT INFORMATION1--800--522--6752 Forlatest revision and Regional CustomerService, All International Rights Reserved visit ourwebsite atwww.tycoelectronics.com TE logo and Tyco Electronics are trademarks. LOCB *Trademark. Otherproducts, logos, and company names used are the property of theirrespective owners.408-9963 PRO-CRIMPERIIIHandCrimpingToolAssembly90760-1 Locator Nut Assembly Tool Frame Locator Insulation Die Retaining Crimper Chamfer Pins Wire Crimper Offset Wire Anvil Chamfer Insulation Die Retaining Anvil Screws Figure 2 2. DESCRIPTION (Figures1 and 2) screw just enough to hold the dies in place. Do not tighten the screw completely at this time. The tool features a tool frame with a stationary jaw 5. Place the wire crimper and insulation crimper so and handle, a moving jaw, a moving handle, and an adjustable ratchet that ensures full contact crimping. that their chamfered sides and their marked The tool frame holds a die assembly with two surfaces face outward, when mounted in the crimping sections. stationary jaw of the tool frame. 6. Insert the two die retaining pins. The die assembly features a wire anvil, an insulation anvil, a wire crimper, and an insulation crimper. 7. Insert the long die retaining screw through the jaw and through both crimper dies, and tighten the Attached to the outside of the frame is a locator screw just enough to hold the dies in place. Do not assembly, which contains a locator, a spring retainer, tighten the screw completely at this time. and a contact support. 8. Carefully close the tool handles, making sure Die retaining pins and die retaining screws are used that the anvils and crimpers align properly. to position and secure the dies in the tool frame. A Continue closing the tool handles until the ratchet nut is used on the upper die retaining screw to hold in the tool frame has engaged sufficiently to hold the locator assembly in place. the anvils and crimpers in place, then tighten both die retaining screws. 3. INSTALLATIONANDREMOVALOFDIESET 9. Place the locator assembly over the end of the ANDLOCATORASSEMBLY (Figure 2) long screw, and position the locator assembly against the side of the tool jaw. 1. Open the tool handles and remove the two die retaining screws from the tool jaws. 10. Place the nut onto the end of the long screw and tighten the nut enough to hold the locator 2. Place the wire anvil and insulation anvil so that assembly in place, while still allowing the locator to their chamfered sides and their marked surfaces slide up and down. face outward, when mounted in the moving jaw of the tool frame. 11. To disassemble, close the tool handles until the ratchet releases, remove the nut, the locator 3. Insert the two die retaining pins. assembly, the two die retaining screws, and the 4. Insert the short die retaining screw through the four die retaining pins, and slide the anvils and jaw and through both anvil dies, and tighten the crimpers out of the tool jaws. 2 of 6 TycoElectronicsCorporation RevB