9-1393303-7 TE Connectivity

Plug-in Maxi ISO Relays Power Relay F7 n Pin assignment similar to ISO 7588 part 1 n Customized versions on request 24VDC versions with contact gap >0.8mm Integrated components (e.g. resistor, diode) Customized marking/color Special covers (e.g. notches, release features, brackets) Typical applications Cross carline up to 70A for example: ABS control, cooling fan, energy management, engine control, glow plug, heated front screen, ignition, lamps: front, rear, fog light, main switch/supply relay. F134J a bw Contact Data Contact Data (continued) 7 Contact arrangement 1 form A, 1 form A, 1 form A, Mechanical endurance >1x10ops. 1 NO 1 NO 1 NO 1) Special high performance 24VDC version with contact gap >0.8mm, part number V23134-A0056-X408 (see part number table). Contact gap - - >0.8mm 2) The values apply to a resistive or inductive load with suitable spark suppression and 1) Rated voltage 12VDC 24VDC 24VDC at maximum 14VDC for 12VDC or 28VDC for 24VDC load voltages. For a load current Limiting continuous current duration of maximum 3s for a make/break ratio of 1:10. 23C 70A 70A 70A 3) Current and time are compatible with circuit protection by a typical automotive fuse. 85C 50A 50A 50A Relay will make, carry and break the specified current. 4) See chapter Diagnostics of Relays in our Application Notes or consult the internet at 125C 30A 30A 30A 2) Plug-in Maxi ISO Relays Power Relay F7 (Continued) Insulation Data Other Data (continued) Initial dielectric strength Terminal type plug-in, QC/ PCB between open contacts 500V Cover retention rms between contact and coil 500V axial force 150N rms between adjacent contacts 500V pull force 150N rms Load dump test push force 150N ISO 7637-1 (12VDC), test pulse 5 V =+86.5VDC Terminal retention s ISO 7637-2 (24VDC), test pulse 5 V =+200VDC pull force 100N s push force 100N 8) resistance to bending 10N 8) Other Data force applied to side 10N EU RoHS/ELV compliance compliant torque 0.3Nm 7) Protection to heat and fire according UL-94 HB or better Weight approx. 38g (1.3oz) Ambient temperature -40 to 125C Resistance to soldering heat THT Climatic cycling with condensation IEC 60068-2-20 260C, 10s EN ISO 6988 6 cycles, storage 8/16h Packaging unit Temperature cycling, plug-in: 210 pcs. IEC 60068-2-14, Nb 10 cycles, -40/+85C (5C/min) plug-in with bracket: 208 pcs. Damp heat cyclic, PCB 315 pcs. IEC 60068-2-30, Db, Variant 1 6 cycles, upper air temp. 55C 7) Refers to used materials. 8) No change in the switching state >1s. Valid for NC contacts, NO contact values Damp heat constant, IEC 60068-2-3, Ca 56 days significantly higher. Category of environmental protection, 8) Values apply 2mm from the end of the terminal. When the force is removed, the terminal IEC 61810 RTI dustproof, RT III sealed must not have moved by more than 0.3mm. Degree of protection, IEC 60529 IP54 (dustproof), IP67 (sealed) Corrosive gas 3 3 IEC 60068-2-42 102cm /m SO , 10 days Accessories 2 3 3 IEC 60068-2-43 10.3cm /m H S, 10 days For details see datasheet Connectors for Maxi ISO Relays 2 Vibration resistance (functional) 8) IEC 60068-2-6 (sine sweep) 10 to 500Hz, min. 5g Shock resistance (functional) 8) IEC 60068-2-27 (half sine) 6ms, min. 30g. Drop test, free fall IEC 60068-2-32 1m onto concrete Terminal Assignment NO NOR NOD 1 form A, NO 1 form A, NO with resistor 1 form A, NO with diode 85 87 85 87 85 87 86 30 86 30 86 30 2 04-2013, Rev. 0413 Catalog and product specification according Catalog and product data is subject to the Catalog product data, Definitions section, www.te.com to IEC 61810-1 and to be used only together terms of the disclaimer and all chapters of application notes and all specifications are 2013 Tyco Electronics Corporation, with the Definitions section. the Definitions section, available at subject to change. a TE Connectivity Ltd. company.