HIRSCHMANN MOBILITY CELLULAR (2G/3G/4G)/ GNSS Screw Antenna CGN 7026 SF S Pt no. 920-641- Combination antenna for positioning and data-services Terrestrial based transmission and satellite-based positioning Designed for installation on vehicles in harsh environmental Subject to alterations Technical data (920-641-001) Cellular Frequency range Low: 698 - 960 MHz High: 1710 - 2690 MHz Services 2G: GSM 850/900 MHz GSM 1800/1900 MHz 3G: UMTS 4G LTE-bands 1 10, 12 20, 23, 25 26 30 33 41, 44 Gain mi n. 0 dBi, max. 3 dBi Polarization Linear vertical Impedance 50 Ohm Return loss typ. > 10 dB Input power 2 W Diagnosis Resistor 10 kOhm GNSS Frequency range GPS (L1): 1563 1587 MHz Galileo (E1): 1559 1591 MHz GLONASS (G1): 1593 1610 MHz Center frequency 1590,0 5 MHz Antenna gain typ. 2 dBic (Gain of passive antenna element) Polarization right handed circular (RHCP) Axial ratio min: 2 dB (In zenith at center frequency) Power supply 3,0 V - 5,5 V Current consumption typ. 35 mA 3 mA LNA gain 21 dB 2 dB (Input and output 50 ) typ. Noise figure 3,0 dB, typ. 2,8 dB (Input and output 50 ) P1dB output 11,5 dBm (F = 1575 MHz) IP3 input >2 dBm (Test tones: F1: 1590 MHz / -30 dBm F2: 1591 MHz / -30 dBm) LNA stopband rejection 1590MHz 60MHz > 60 dBc (Input to output of LNA) Isolation GNSS/ Cellular GNSS > 20 dB ( S21 of active antenna from Cellular to GNSS connector in the GNSS frequency ranges) Isolation GNSS / Cellular 2G/3G/4G Frequencies > 5 0 d B ( S 2 1 o f a c t iv e antenna from Cellular to GNSS connector in the Cellular frequency ranges) TE CONNECTIVITY TRANSPORTATION SOLUTIONS /// CELLULAR (2G/3G/4G)/ GNSS Screw Antenna 07/2019 Page 1 CELLULAR (2G/3G/4G)/ GNSS SCREW ANTENNA CGN 7026 SF S Pt no. 920-641- Output impedance 50 Output VSWR 1,5 Mechanical Round mounting hole diameter / mm typ. 20 max. 20,5 Thickness holder mm min. 0,5 max. 6,0 Radius of curvature / mm min. 1500 max. planar Free space under mounting place / mm min. h=25 x 35 Nut PA6.6 GF30 white Thread bolt diameter 18 x 1.5 mm Tightening torque / Nm min. 6 max. 7 Connector pulling force typ. > 80 N Cable pulling force typ. > 80 N Weight ca. 296 g Dimensions 95 mm x 57 mm x 69 mm Environmental Operation and storage temperature range -40 C typ. 80 C max. Humidity Non-condensing 55 C 95% RH Protection levels For all antenna parts placed outside of the vehicle: IP 6K9K (ISO 20653) For the cable inlet of the antenna: IP67 Scope of supply Antenna with hexagonal nut 1) dBic: referenced to an isotropic radiator, circular polarization 2) dBi: referenced to an isotropic radiator Cable type CELL GNSS Versions 920-641-101 CGN 7026 SF S RG 174 200 mm FAKRAm, Code D 150 mm FAKRAm, Code C Block Diagram TE CONNECTIVITY TRANSPORTATION SOLUTIONS /// CELLULAR (2G/3G/4G)/ GNSS Screw Antenna 07/2019 Page 2