HIRSCHMANN MOBILITY WLAN (2.4GHz/5.8GHz) Screw Antenna WLAN 2458 LP S MIMO/series Pt no. 951-001- Low Profile antenna Mount on any surfaces (e.g. plastics, metal...) For WLAN networks (2,4 GHz or/and 5,8 GHz) Subject to alterations Diagnostic resistance possible on MIMO 2 Public transport or building indoor & outdoor, M2M application maintenance, Technical data Electrical Specification Frequency range Bluetooth: 2400 - 2484 MHz IEEE 802.11 b, g, n, ax: 2412 - 2484 MHz IEEE 802.11 a, h, n, ac, ax: 5150 - 5 7 2 5 MHz IEEE 802.11 n: 2400 - 2484 MHz 5150 - 5725 MHz IEEE 802.11 p: 5755 - 5925 MHz Impedance 50 Ohm VSWR 2400 2485 MHz 1,6 5150 5925 MHz 1,6 Polarization Linear, vertical Gain (linear gain, vetical polarization) 2400 2485 MHz 2,5 dBi* 5150 5925 MHz 3 dBi* Isolation Port 1-2 & 2-3 (for MIMO3) > 10 dB Port 1-3 (2400 - 2485 MHz) > 16 dB Port 1-3 (5150 - 5925 MHz) > 18 dB Load capacity IEEE 802.11 b, g, n, ax: 2 0 0 mW IEEE 802.11 a, h, n, ac, ax: 1000 mW IEEE 802.11 n: 200 mW (2,4 - 2,84 GHz) 1000 mW (5,1 - 5,72 GHz) IEEE 802.11 p: 8 W EIRP (5,79 - 5,81 GHz) 2 W EIRP (5,85 - 5,92 GHz) Mechanical Dimensions ca. 124 mm x 80 mm x 31 mm Housing Materials ASA-PC Weight 270 g Operations temperature range - 40 + 85 C Storage temperature range - 40 + 85 C Housing protection class IP66 (acc. IEC 60529) RG174 Low Loss (long dimensions not adapted Cable type to WLAN >5 GHz) Versions 951-001-001 MIMO 3 SMAm 0,15 x 3 140/170/200 +30 mm SMA male straight w o 951-001-002 MIMO 2 SMAm 0,15 x 2 140/200 +30 mm SMA male straight * dBi: referenced to an isotropic radiator Technical drawings TE CONNECTIVITY TRANSPORTATION SOLUTIONS /// WLAN (2.4GHz/5.8GHz) Screw Antenna 02/2020 Page 1 WLAN (2.4GHz/5.8GHz) SCREW ANTENNA WLAN 2458 LP S MIMO/series Pt no. 951-001- 124 mm Installation Take the necessary electrostatic precautions for a connection of electronic components (Potential ESD < 1 KV) Surface must be flat (maximum radius 1mm per meter), max thickness 10 mm No metallic (conductive) surface above the antenna Connectors are not waterproof, so area below the antenna must be dry Drill a hole (diameter 15 +4/-0,5mm) (clean with isopropyl alcohol or similar) Screw the nut on the grounding plate (Torque 5 Nm +0-20%) No adjunction of any material (silicones, glue, ) Check that the coaxial cable is not electrically charged (Potential ESD < 1 KV) Connect the coaxial cable connector by hand without forcing (Torque 1 +/- 0,15 Nm = handmade) Check that the wires respect the appropriate way, not pulled / stressed / bended < 25mm radius / touching aggressive parts www.te.com/hirschmann-mobility hirschmann-mobility te.com TE, TE Connectivity, TE connectivity (logo), and EVERY CONNECTION COUNTS are trademarks. Hirschmann is a trademark. Bluetooth is a trademark. The information given herein, including drawings, illustrations and schematics which are intended for illustration purposes only, is believed to be reliable. However, TE Connectivity makes no warranties as to its accuracy or completeness and disclaims any liability in connection with its use. TE Connectivitys obligations shall only be as set forth in TE Connectivitys Standard Terms and Conditions of Sale for this product and in no case will TE Connectivity be liable for any incidental, indirect or consequential damages arising out of the sale, resale, use or misuse of the product. Users of TE Connectivity products should make their own evaluation to determine the suitability of each such product for the specific application. 2020 TE Connectivity Ltd. family of companies All Rights Reserved. TE CONNECTIVITY TRANSPORTATION SOLUTIONS /// WLAN (2.4GHz/5.8GHz) Screw Antenna 02/2020 Page 2