9840530001 TE Connectivity

CUSTOMER DRAWING Slit Adhesive Sleeve (S-1017) Table 1: Dimensions (inches) PART DESCRIPTION EXTRUDED ID CUT LENGTH EXTRUDED WALL (A) (B) (C) SAS-090-038-1017 .090 .005 0.38 .050 0.024 .005 SAS-090-075-1017 .090 .005 0.75 .050 0.024 .005 SAS-090-1-1017 .090 .005 1.00 .050 0.024 .005 SAS-115-075-1017 .115 .005 0.75 .050 0.032 .005 SAS-115-1-1017 .115 .005 1.00 .050 0.032 .005 SAS-160-075-1017 .160 .005 0.75 .050 0.032 .005 SAS-160-1-1017 .160 .005 1.00 .050 0.032 .005 SAS-200-075-1017 .200 .005 0.75 .050 0.035 .005 SAS-200-1-1017 .200 .005 1.00 .050 0.035 .005 Color: Amber TITLE: Tyco Electronics Corp. Raychem 300 Constitution Drive, SPLIT ADHESIVE SLEEVE Menlo Park, CA. 94025 Molded Parts DOCUMENT NO.: Unless otherwise specified, dimensions are in inches. Metric dimensions are shown in brackets SAS-XXX-XXX-1017 TOLERANCES: ANGLES: Tyco Electronics reserves the right to amend this 0.00 N/A N/A drawing at any time. Users should evaluate the REVISION: DATE: 0.0 N/A suitability of the product for their application. 0 N/A ROUGHNES D August 14, 2008 S IN MICRON PREPARED BY: ECO NUMBER: CAGE CODE : SCALE: SIZE: SHEET: UNGUYEN ECO-08-020204 06090 -NA- A 1 of 3 2004 2008 Tyco Electronics Corporation. All rights reserved. If this document is printed it becomes uncontrolled. Check for the latest revision. CUSTOMER DRAWING Table 2: Properties Property Unit Requirements Test Method Physical Visual -- No foreign matter, voids, pinholes. Specific Gravity -- 0.95 0.05 ASTM D 792 Softening Point C 120 10 ASTM E 28 Low Temperature C -20 maximum ASTM D 746 Impact Brittleness Adhesive Peel lbs/in width Note 1 Polyolefin 20 minimum Polychloroprene 10 minimum Polyvinylchloride 15 minimum Chemical* Water Absorption Percent 1.0 maximum ASTM D 570 Fungus Resistance -- Rating of 1 or less ASTM G 21 Fluid Resistance* Percent ASTM D 543 Weight Change after 7 days/23 3C (75 5F) 3 X 1-inch specimens Detergent Solution ( 12) 3 maximum Hydraulic Fluid (MIL-PRF-87257 10 maximum or MIL-PRF-83282 ) Lube Oil (MIL-PRF-7808L) 5 maximum ASTM Oil ( 49) 15 maximum Electrical* 10 Volume Resistivity ohm-cm 10 minimum ASTM D 257 Dielectric Strength V/mil 500 minimum ASTM D 149 *Test specimens shall be prepared in the form of 6 x 6 x .075-inch compression molded slabs. Molding temperature shall be 150 3C (302 5F). Acceptance Tests: Visual, Dimensions, Specific Gravity DOCUMENT NO.: ECO NUMBER: REV.: DATE: SHEET: ECO-08-020204 August 14, 2008 SAS-XXX-XXX-1017 D 2 of 3 2004 -2008Tyco Electronics Corporation. All rights reserved. If this document is printed it becomes uncontrolled. Check for the latest revision.