BND40AC00-1204A TE Connectivity

ASSY USED ON: BAND (SUPPLIED FLAT) 3 8 (SEE PART NUMBER BREAKDOWN FOR OPTIONS) CODE 40 - BANDING BACKSHELL BNX40AB00-1608 -S SERIES BNX - BAND STRAP NOT INCLUDED BND - BAND STRAP INCLUDED (SEE BAND TERMINATION CONFIGURATION) CONNECTOR INTERFACE MATERIAL REFER TO CH00-0250-016 FINISH REFER TO CH00-0250-016 ANGLE ORDER NUMBER (TABLE 1) ENTRY SIZE (TABLE 2) BAND TERMINATION CONFIGURATION 3 8 V - ONE STEP STANDARD BAND W - ONE STEP MICROBAND U - TWO STEP STANDARD BAND FOR BNX, LEAVE BLANK OPTION FIELD SEPARATOR MODIFICATION CODE REFER TO CH00-0250-016 2 NOTES: 1. THIS PRODUCT IS DESIGNED TO TERMINATE A BRAIDED CABLE SHIELD BY MEANS OF A BAND STRAP AND A HEAT SHRINKABLE LIPPED BOOT TO A CONNECTOR. 2. FOR ADDITIONAL DIMENSIONS, ORDERING INFORMATION AND MODIFICATIONS, SEE CH00-0250-016. 3. SEE DRAWING BND-XXXXX FOR MORE INFORMATION. 4. BACKSHELL TO BE PERMANENTLY MARKED WITH CODE IDENTIFICATION NUMBER AND FULL BASIC PART NUMBER (e.g. 06090-BND40AB00-1814). BACKSHELL TO BE MARKED WITHBN EVEN IF NO BAND IS ORDERED. THE BAND TERMINATION CONFIGURATION CODE IS FOR ORDERING INFORMATION ONLY AND IS NOT A PART MARKING REQUIREMENT. 5. ALL ENTRY SIZES ARE SHOWN IN TABLE 2. MAXIMUM ENTRY SIZES ARE SHOWN IN TABLE 1. IF MAX ENTRY IS EXCEEDED, A 2 PIECE BACKSHELL ASSEMBLY (TYPE 2) IS SUPPLIED. SEE CH00-0250-016 FOR FURTHER DETAILS. 6. BACKSHELL MATES TO MIL-DTL-38999, SERIES III AND IV, CLASS C, F, K, AND W, D38999/20, /24, /26, /40, /46 AND /47 CONNECTORS, AND WHEN SO MATED SHALL PROVIDE A WATER-TIGHT SEAL MEETING THE REQUIREMENTS OF MIL-C-85049, PARA. 3. 5. 7. 7. THESE DIMENSIONS APPLY IF A SELF-LOCKING COUPLING NUT IS USED 8. V AND U BANDS ARE SUITABLE FOR ENTRY SIZES 03-24, W IS SUITABLE FOR ENTRY SIZES 03-12 ONLY. CONTACT FACTORY FOR BAND OPTIONS ON LARGER ENTRY SIZES. DATE 3RD ANGLE K.WINCZURA DRAWN PROJECTION TITLE: 15/09/2015 NOT TO CHECKED 15/09/2015 SCALE BANDING BACKSHELL UNLESS OTHERWISE SPECIFIED APPROVED K.SHEPPARD 15/09/2015 ALL DIMENSIONS IN MILLIMETRES GENERAL TOL LINEAR +/-0,25MM APPROVED H.SMITH 15/09/2015 ANGULAR +/- 1 REVISIONS LTR DATE APPROVED DESCRIPTION MIL-DTL-38999 SERIES III & IV F 15/09/2015 H.SMITH REVISED PER ECO-15-010973 G REVISED PER ECO-15-016545 17/11/2015 H.SMITH TE CONNECTIVITY - POLAMCO LTD RESERVES THE RIGHT TO AMEND THIS DRAWING DRAWING NO: DRAWING REV: SHT TE CAGE CODE: 06090 AND THE INFORMATION SET FORTH HEREON AT ANY TIME. USERS SHOULD INDEPENDENTLY EVALUATE THE SUITABILITY OF THE PRODUCT FOR THEIR APPLICATION. BND40A G 1 POLAMCO/TE CAGE CODE: U5792G D ASSY USED ON: IF MAX ENTRY IS EXCEEDED BACKSHELL WILL BE SUPPLIED AS TYPE 2 30,00 16,80`0,50 30,00 18,00 SILICONE O-RING 3,50 13,00 PART MARK 5 HERE PART MARK STRAIGHT BACKSHELL - TYPE 2 STRAIGHT BACKSHELL - TYPE 1 HERE C 16,80`0,50 F 45 BACKSHELL - TYPE 1 45 BACKSHELL - TYPE 2 W H 16,80`0,50 T M 90 BACKSHELL - TYPE 1 90 BACKSHELL - TYPE 2 H W 16,80`0,50 T M 90 BACKSHELL - TYPE 1 90 BACKSHELL - TYPE 2 STAINLESS STEEL AND STAINLESS STEEL AND NICKEL ALUMINIUM BRONZE NICKEL ALUMINIUM BRONZE DATE 3RD ANGLE K.WINCZURA DRAWN PROJECTION TITLE: 15/09/2015 NOT TO CHECKED 15/09/2015 SCALE BANDING BACKSHELL UNLESS OTHERWISE SPECIFIED APPROVED K.SHEPPARD 15/09/2015 ALL DIMENSIONS IN MILLIMETRES GENERAL TOL LINEAR +/-0,25MM APPROVED H.SMITH 15/09/2015 ANGULAR +/- 1 REVISIONS LTR DATE APPROVED DESCRIPTION MIL-DTL-38999 SERIES III & IV F 15/09/2015 H.SMITH REVISED PER ECO-15-010973 G REVISED PER ECO-15-016545 17/11/2015 H.SMITH TE CONNECTIVITY - POLAMCO LTD RESERVES THE RIGHT TO AMEND THIS DRAWING DRAWING NO: DRAWING REV: SHT TE CAGE CODE: 06090 AND THE INFORMATION SET FORTH HEREON AT ANY TIME. USERS SHOULD INDEPENDENTLY EVALUATE THE SUITABILITY OF THE PRODUCT FOR THEIR APPLICATION. BND40A G 2 POLAMCO/TE CAGE CODE: U5792 B A THREAD XXXX E Z S Y E K B A THREAD XXXX J J