Specification Control CEC-RWC-18664 R Drawing 4 conductor cable Issue N - 6/12/2015 Identification, colors & marks Cross section A 2L A B A 4L 5L A 6L Components ID Quantity Part number Description A 4 RAYFOAM-H2444C4 Dielectric B 1 FEP Filler .018 Filler Cable Outer Description Thickness OD Inches mm Inches mm Layer 1 0.106 2.68 Wrap Fluoropolymer Wrap .002 0.004 0.10 0.114 2.88 Wrap Al.-PET .002 - Al. facing out 0.004 0.10 0.122 3.09 Shield Round tinned copper 38 awg regular 0.009 0.22 0.139 3.52 Jacket FEP clear 0.010 0.25 0.159 4.03 Cable OD tolerance + 0.006 + 0.15 - 0.006 - 0.15 Specification Raychem Spec.1200 Weight 21.56 lb/kft 32.14 Kg/Km Page 1 of 3 This specification sheet takes precedence over documents referenced herein. Referenced documents shall be of the issue in effect on date of invitation to bid. Proposed specification control drawings may be altered prior to final issue. RCD Version 1.2 Level 1 Ser 5 RWC 8/7/95Specification Control CEC-RWC-18664 R Drawing 4 conductor cable Issue N - 6/12/2015 Continued Physical properties Jacket elongation 200% minimum Jacket tensile strength 2000 psi minimum Shield Coverage 85% minimum Wrap (each) 25% (minimum) overlap Marker Tape There shall be a marker tape under the jacket: RAYCHEM CEC-RWC-18664 06090 A - . every other mark is an inverted mirror image. The orientation of the tape shall be as follows: The end components shall be Red, Green, Blue and Yellow in a clockwise direction. The end components shall be Red, Yellow, Blue, and Green in a clockwise direction. Environmental properties Shall meet the requirements of FAR Part 25, Appendix F, Part I when tested in Flammability accordance with the 60 degree test specified therein. Electrical properties Voltage withstand (dielectric) 1000 volts (rms) conductor to conductor and shield 500 volts (rms) shield to shield when applicable per NEMA WC 27500. Coax components to their own SCD. Jacket Flaws Spark Test: 2.5 kV (rms) Impulse Dielectric Test: 6.0 kV (peak) See Page 3 Additional Electricals Notes Colors Color code designators shall be in accordance with MIL-STD-681. Dimensions Dimensions are in inches, and unless otherwise designated, are nominal. Export License Note The information contained on this drawing may be subject to International Traffic in Arms Regulations (ITAR) or Export Administration Regulations (EAR) controls and may not be disclosed to any foreign person or firm, including foreign persons employed by or associated with your firm, without first complying with all requirements for obtaining an export license if applicable. Identification, Colors & Marks The following is the key to the descriptions in the left hand view of the cable on Page 1. Line 1: Identifies the component per the components ID list. Line 2: Color codes. Line 3: Mark on component mark on component jacket. Minimum length Cable will be supplied in 50 ft. minimum lengths unless otherwise specified. Part Number Note Other codes and suffixes may be added to the Part Number as necessary, to capture any additional requirements imposed by the purchase order Specification Information This drawing is the property of Tyco Electronics Corporation and may not be used for any purpose other than for that which it is supplied without the express written authority of Tyco Electronics Corporation. Raychem, Rayfoam, TE Connectivity, TE connectivity (logo) and TE (logo) are trademarks. Trademarks Page 2 of 3 This specification sheet takes precedence over documents referenced herein. Referenced documents shall be of the issue in effect on date of invitation to bid. Proposed specification control drawings may be altered prior to final issue. RCD Version 1.2 Level 1 Ser 5 RWC 8/7/95