D369-P66-NP3 TE Connectivity

D369-P33-NP1 K1316 H++++D 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 A NOTES: 3 WAY CONNECTOR 1 MARKED WITH TE PART NUMBER, CAGE CODE AND DATE CODE. PART NUMBER EXAMPLE: D369 - H P 3 3 - N P 1 24.86 MAX. 12.85 MAX. BASIC PART NUMBER CONTACT CONFIGURATION 4 2.50 MIN. HARSH ENVIRONMENT CONTACT TYPE (P=PIN, S=SKT) D1 B B SLOT 2 (OMIT FOR CABIN VARIANT ) SHELL KEYING SHELL STYLE (P=PLUG) SHELL SIZE (3, 6 OR 9) CONTACT QUANTITY B (3=3 x 22, 6=6 x 22, 9=9 x 22) +Y -Y C BOEING PART NUMBER EXAMPLE: BACC65CP 1 P N C MARKED ON BASIC PART NUMBER SHELL KEY BAG ONLY SHELL SIZE CONTACT TYPE 0.35 MAX. D2 (1=SIZE 3, 2=SIZE 6, 3=SIZE 9) (PIN=PIN, S=SKT) SHELL TO SHELL BUTTON ALIGNMENT RIBS DEPRESSED -X +X BOEING PART STANDARD BACC65CP REVISION B REFERS. POSITION N.B. BACC65CP*** PART NUMBERS ARE SUPPLIED WITHOUT CONTACTS. A D D 2 PERFORMANCE: CABIN CONNECTOR HARSH ENVIRONMENT CONNECTOR D369-P**-*** D369-HP**-*** OR BACC65CP*** 9 COORDINATE POSITIONS OF CONTACTS (3 WAY CONNECTOR ONLY) TEMPERATURE RANGE -55 C TO +175 C DIELECTRIC WITHSTAND 1500VRMS <2mA LEAKAGE CONTACT LOCATION CONTACT VOLTAGE (AT SEA LEVEL) POSITION (ID) X AXIS (mm) Y AXIS (mm) DURABILITY 500 MATING CYCLES MIN. E E 1 -2.54 0 INSULATION RESISTANCE 5000 M INITIAL 2 0 0 IP RATING IP65 IP67 3 2.54 0 SEALING RTCA DO160 - CATEGORY A4 (15,000ft) EN2591-314: 12.1kPa (1.75psi) 15km (50,000ft) HUMIDITY RTCA DO160 - CATEGORY A EN2591-321 / EIA-364-31 METHOD IV 1 PART MARKING 3. INSERTION / EXTRACTION TOOL (M81969/14-01 OR EQUIVALENT) SUPPLIED SEPARATELY. F F 9.35 4 CONTACT CONFIGURATION: 8.67 (PIN INSERT) CONTACT P/N (OR EQUIVALENT) CRIMP POSITIONER CONTACT CRIMP WIRE CURRENT CONFIG. DESCRIPTION TOOL ACCOMODATION RATING PIN SOCKET PIN SOCKET 0 NO CONTACTS SUPPLIED CRIMP, COPPER 1 38941-22L 38946-22L M22520/2-09 M22520/2-06 M22520/2-01 22-28 AWG 5A (22 AWG) WIRE CRIMP, ALUMINIUM G G 2 200-1042-22 200-1142-22 KAL2 ALNP 22-A 22 AWG 5A WIRE CRIMP, ENLARGED 3 182-0860-22 182-0862-22 M22520/2-09 M22520/2-06 M22520/2-01 20-24 AWG 5A (20 AWG) COPPER WIRE 5. MATERIALS: PIN / MALE CONTACT CAVITY IDENTIFICATION ON REAR MATERIAL COMPONENT (FINISH: CLEAN IN ALL CASES) H H SEALS SILICONE / FLUOROSILICONE BLEND RUBBER BODY / INSERT THERMOPLASTIC COMPONENTS 4.12 3.50 (SOCKET INSERT) 6. IF FILLER PLUGS ARE REQUIRED, USE THE FOLLOWING: TE PART NUMBER - 600300-22. SHELL COLOUR IS KEYING MIL-SPEC PART NUMBER - MS27488-22-2. DEPENDANT (SEE TABLE) J J 7. MAXIMUM WEIGHTS (WITHOUT CONTACTS): ACCESSORY OR 3 WAY - 1.9g (PIN INSERT), 2.0g (SOCKET INSERT). BOOT MOUNTING 6 WAY - 2.4g (PIN INSERT), 2.6g (SOCKET INSERT). FEATURE 9 WAY - 3.0g (PIN INSERT), 3.2g (SOCKET INSERT). 8 FOR ALL HARSH ENVIRONMENT VARIANTS, THE REAR BODY IS TO BE COLOURED DARK BLUE. 9 DIMENSIONS ARE TRUE POSITIONS OF CAVITIES AT FRONT OF PIN INSERT (SOCKET OPPOSITE). K K CENTRE OF EACH CAVITY 0.20 A B . SOCKET / FEMALE CONTACT CAVITY IDENTIFICATION ON REAR CABLE TIE SLOT SHELL KEYING (ALL SIZES) POSITIONS (0.03) REAR WIRE SEAL ORIENTATION COLOUR D1 D2 8 REAR BODY N BLACK -2.35 2.90 L A DARK RED -2.35 -2.90 L MATERIAL: FINISH: B DARK BLUE -1.175 -2.90 BS8888 SEE NOTES C DARK GREEN 0 -2.90 THIRD ANGLE PROJECTION D YELLOW 1.175 -2.90 TYPE: CUSTOMER DRAWING TITLE: UNLESS OTHERWISE STATED: TE CONNECTIVITY UK LTD., 369 PLUG CONNECTOR, DIMENSIONS: mm INCHES ST. LEONARDS-ON-SEA, TN38 9RF, UK. ENVELOPE DRAWING SIZE: SCALE: DRAWING NUMBER: SHEET: ISSUE: AB DUK-70190 JCB RJM NDL CEO 04/02/2019 M M IF IN DOUBT, ASK IF IN DOUBT, ASK A1 5:1 1 OF 2 AB APP. ISSUE CHANGE NOTE DRAWN CHECKED APP. ENG. DATE 611252-ENV MARKETING 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 THIS INFORMATION IS CONFIDENTIAL AND PROPRIETARY TO TYCO ELECTRONICS CORPORATION AND ITS WORLDWIDE SUBSIDIARIES AND AFFILIATES (TE). IT MAY NOT BE DISCLOSED TO ANYONE, OTHER THAN TE PERSONNEL, WITHOUT AUTHORIZATION FROM TE (www.TE.com). DRAWING NUMBER: 611252-ENV 4.75 MAX. 9.89 MAX. 1.05 MIN. SLOT 10.40 MAX. (BUTTON)D369-P66-NP1 K1316 H++++D D369-P99-NP1 K1316 H++++D 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 A 9 WAY CONNECTOR 6 WAY CONNECTOR 24.86 MAX. 12.85 MAX. 24.86 MAX. 2.50 MIN. D1 12.85 MAX. B B 2.50 MIN. SLOT SLOT D1 B B +Y C C +Y -Y -Y 0.35 MAX. D2 0.35 MAX. BUTTON D2 SHELL TO SHELL BUTTON D D DEPRESSED -X +X ALIGNMENT RIBS DEPRESSED POSITION -X +X A POSITION A 9 COORDINATE POSITIONS OF CONTACTS COORDINATE POSITIONS OF CONTACTS 9 (6 WAY CONNECTOR ONLY) (9 WAY CONNECTOR ONLY) E E CONTACT LOCATION CONTACT CONTACT LOCATION CONTACT POSITION (ID) X AXIS (mm) Y AXIS (mm) POSITION (ID) X AXIS (mm) Y AXIS (mm) 1 -2.54 1.27 1 -2.54 2.54 2 0 1.27 2 0 2.54 3 2.54 1.27 3 2.54 2.54 4 2.54 -1.27 4 2.54 0 5 0 -1.27 F F 1 PART MARKING 5 0 0 6 -2.54 -1.27 1 PART MARKING 6 -2.54 0 4.12 7 -2.54 -2.54 3.50 8 0 -2.54 (SOCKET INSERT) 9 2.54 -2.54 4.12 3.50 (SOCKET INSERT) G G H H SOCKET / FEMALE CONTACT CAVITY IDENTIFICATION ON REAR 9.35 8.67 9.35 (PIN INSERT) 8.67 (PIN INSERT) J J SOCKET / FEMALE CONTACT CAVITY IDENTIFICATION ON REAR K K PIN / MALE CONTACT CAVITY IDENTIFICATION ON REAR L L MATERIAL: FINISH: BS8888 SEE NOTES THIRD ANGLE PROJECTION PIN / MALE TYPE: CUSTOMER DRAWING TITLE: CONTACT CAVITY UNLESS OTHERWISE STATED: IDENTIFICATION ON REAR TE CONNECTIVITY UK LTD., 369 PLUG CONNECTOR, DIMENSIONS: mm INCHES ST. LEONARDS-ON-SEA, TN38 9RF, UK. ENVELOPE DRAWING SIZE: SCALE: DRAWING NUMBER: SHEET: ISSUE: M M IF IN DOUBT, ASK A1 5:1 2 OF 2 AB 611252-ENV 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 THIS INFORMATION IS CONFIDENTIAL AND PROPRIETARY TO TYCO ELECTRONICS CORPORATION AND ITS WORLDWIDE SUBSIDIARIES AND AFFILIATES (TE). IT MAY NOT BE DISCLOSED TO ANYONE, OTHER THAN TE PERSONNEL, WITHOUT AUTHORIZATION FROM TE (www.TE.com). DRAWING NUMBER: 611252-ENV 9.89 MAX. 9.83 MAX. 1.05. MIN. SLOT 15.50 MAX. (BUTTON) 9.89 MAX. 7.29 MAX. 1.05 MIN. SLOT 12.95 MAX. (BUTTON)