JMGAT-12MW TE Connectivity

CII Low Signal Relays Double Pole, Electrically Held, 1 Amp and Less (Continued) MGAT MGAT Standard .100 Grid Diode Suppressed/MOSFET Driven High Performance Relay Qualified to MIL-R-28776/6 X2 G X1 + A2 B2 A1 B1 A3B3 Terminal View Product Facts n MOSFET driver, zener & suppression diodes n Hermetically sealed n High shock & vibration ratings n Mounting pads n Excellent RF switching Electrical Characteristics Contact Ratings Contact Arrangement Contact Operations Type Load Min. 2 Form C (DPDT) 1.0 A 28 Vdc Resistive 100,000 Contact Material 250 mA 115 Vac, 60 Hz & 400 Hz Resistive (case not grounded) 100,000 Stationary Gold/platinum/palladium/silver 100 mA 115 Vac, 60 Hz & 400 Hz Resistive 100,000 (gold plated) 0.2 A 28 Vdc Inductive (0.32 Henry) 100,000 Moveable 0.1 A 28 Vdc Lamp 100,000 Gold/platinum/palladium/silver 30 A 50 mVdc Low Level 1,000,000 (gold plated) 0.1 A 28 Vdc Intermediate Current 50,000 Contact Resistance Before Life 100 milliohms max. (measured 10 mA 6 Vdc) After Life 200 milliohms max375 (9.40) MAX (measured 1 A 28 Vdc) .335 (8.51) MAX .435 (11.05) MAX .035 .031 .003 (0.79) Mechanical Life Expectancy (0.98) 1 million operations 280 (7.11) MAX Coil Voltage 5 to 26.5 Vdc .100 Coil Power 660 mW max. 25C (2.54) .475 (11.94) Duty Cycle Continuous T MAX Pick-up Voltage Approximately 50% of nominal coil voltage pad) Pick-up Sensitivity (0.43) DIA + .017 (0.43) DIA +.002 .100 130 mW max. 25C GROUND PIN -.001 9 PINS (2.54) MGAT .370 (9.40) MAX (OPTIONAL) MGAT Header MGAT Enclosure 1-26 Catalog 5-1773450-5 Dimensions are shown for Dimensions are in millimeters USA: +1 800 522 6752 For additional support numbers Revised 3-13 reference purposes only. unless otherwise specified. Asia Pacific: +86 0 400 820 6015 please visit www.te.com Specifications subject UK: +44 800 267 666 www.te.com to change.CII Low Signal Relays CII Low Signal Relays Double Pole, Electrically Held, 1 Amp and Less (Continued) Operating Characteristics Environmental Characteristics Semiconductor Characteristics MGAT (Continued) Timing Temperature Range Diode Operate Time 2.0 ms max. -65C to +125C 100 Vdc peak inverse voltage (PIV) 1 Contact Bounce 1.5 ms max. 1.0 Vdc max. transient voltage Weight Dielectric Withstanding Voltage 0.09 oz. (2.55 gms) Zener Diode Between Open Contacts 0.129 oz. (3.45 gms) w/ mounting pad 20 Vdc 3 Vdc over temperature range 500 Vrms 60 Hz attached MOSFET Between Adjacent Contacts Vibration Resistance 0.5 Vdc min. gate turn-off voltage 500 Vrms 60 Hz 30 Gs, 10 to 3,000 Hz 4.3 Vdc max. gate turn-on voltage Between Contacts & Coil Shock Resistance 500 Vrms 60 Hz 75 Gs, 6 1 ms max. Insulation Resistance QPL Approval 10,000 megohms min. 500 Vdc MIL-R-28776/6 (JMGAT) 1,000 megohms 500 Vdc (coil to case +125C) .014 (0.36) .094 (2.39) DIA FULL R 2 PLS .256 (6.50) .140 .170 (3.564.32) MGAT Mounting Pad Coil Data Coil Nom. Coil Circuit Coil Circuit Pickup Pickup Drop-Out Drop-Out Nom. Coil Resistance Max. Coil Current Current Voltage Voltage Voltage Voltage Power Coil in Ohms Coil Voltage mA (Max.) mA (Min.) Vdc (Max.) Vdc (Max.) Vdc (Min.) Vdc (Min.) (mW) Desig. 10% 25C Voltage (Vdc) (Note) (Note) 25C 125C 25C -65C 25C (Note) MGAT 5.0 39 132.3 96.5 2.9 3.5 0.23 0.13 641 5.8 5 6.0 78 83.9 60.3 3.5 4.5 0.32 0.18 462 8.0 6 9.0 220 47.1 33.1 5.3 6.8 0.48 0.27 368 12.0 9 12.0 390 36.1 24.9 7.1 9.0 0.65 0.36 369 16.0 12 18.0 880 24.1 16.1 10.6 13.5 0.97 0.54 368 24.0 18 26.5 1,560 19.9 12.9 14.2 18.0 1.30 0.72 450 32.0 26 Note: Coil resistance not directly measurable. Coil current should be within limits shown when tested at nominal voltage at 25C for 5 seconds max. Ordering Instructions Catalog-selected Relays: The catalog number is derived by choosing the proper CODE for each of the relay characteristics in the order in which the codes are listed. Specifying a Part Number Example: Type Terminals Diodes Ground Pins Coils Mounting Pads MGA CT G -26 W * The part number example shown on this page is for catalog items. For a list of specific QPL part numbers, please see the index in Section 15. 1-27 Catalog 5-1773450-5 Dimensions are shown for Dimensions are in millimeters USA: +1 800 522 6752 For additional support numbers Revised 3-13 reference purposes only. unless otherwise specified. Asia Pacific: +86 0 400 820 6015 please visit www.te.com Specifications subject UK: +44 800 267 666 www.te.com to change.