JMGST-5LW TE Connectivity

CII Low Signal Relays Double Pole, Electrically Held, 1 Amp and Less (Continued) MGST MGST Sensitive .100 Grid Diode Suppressed/MOSFET Driven High Performance Relay Qualified to MIL-R-28776/7 X2 G X1 + A2 B2 A1B1 A3 B3 Terminal View Product Facts n MOSFET driver, zener & suppression diodes n Hermetically sealed n High shock & vibration ratings n Mounting pads n Excellent RF switching Electrical Characteristics Contact Ratings Contact Arrangement Contact Operations Type Load Min. 2 Form C (DPDT) 1.0 A 28 Vdc Resistive 100,000 Contact Material 250 mA 115 Vac, 60 Hz & 400 Hz Resistive (case not grounded) 100,000 Stationary Gold/platinum/palladium/silver 100 mA 115 Vac, 60 Hz & 400 Hz Resistive 100,000 (gold plated) 0.2 A 28 Vdc Inductive (0.32 Henry) 100,000 Moveable 0.1 A 28 Vdc Lamp 100,000 Gold/platinum/palladium/silver 30 A 50 mVdc Low Level 1,000,000 (gold plated) 0.1 A 28 Vdc Intermediate Current 50,000 Contact Resistance Before Life 100 milliohms max. (measured 10 mA 6 Vdc) .335 (8.51) MAX .435 (11.05) MAX After Life 200 milliohms max375 (9.40) MAX (measured 1 A 28 Vdc) .035 .031 .003 (0.79) (0.98) Mechanical Life Expectancy .375 (9.53) 1 million operations MAX Coil Voltage 5 to 26.5 Vdc .100 (2.54) .475 Coil Power 565 mW max. 25C (11.94) MAX Duty Cycle Continuous T Pick-up Voltage Approximately ng pad) 50% of nominal coil voltage Pick-up Sensitivity .100 GROUND PIN (2.54) (0.43) DIA + .017 (0.43) DIA +.002 60 mW max. 25C (OPTIONAL) -.001 9 PINS M GST .370 (9.40) MAX MGST Header MGST Enclosure 1-28 Catalog 5-1773450-5 Dimensions are shown for Dimensions are in millimeters USA: +1 800 522 6752 For additional support numbers Revised 3-13 reference purposes only. unless otherwise specified. Asia Pacific: +86 0 400 820 6015 please visit www.te.com Specifications subject UK: +44 800 267 666 www.te.com to change.CII Low Signal Relays CII Low Signal Relays Double Pole, Electrically Held, 1 Amp and Less (Continued) Operating Characteristics Environmental Characteristics Semiconductor Characteristics MGST (Continued) Timing Temperature Range Diode Operate Time 4.0 ms max. -65C to +125C 100 Vdc peak inverse voltage (PIV) 1 Release Time 7.5 ms max. 1.0 Vdc max. transient voltage Weight Contact Bounce 1.5 ms max. 0.09 oz. (2.55 gms) Zener Diode Dielectric Withstanding Voltage 0.129 oz. (3.45 gms) w/ mounting pad 20 Vdc 3 Vdc over temperature range Between Open Contacts attached MOSFET 500 Vrms 60 Hz Vibration Resistance 0.5 Vdc min. gate turn off voltage Between Adjacent Contacts 30 Gs, 10 to 3,000 Hz 4.3 Vdc max. gate turn on voltage 500 Vrms 60 Hz Shock Resistance Between Contacts & Coil 75 Gs, 6 1 ms max. 500 Vrms 60 Hz QPL Approval Insulation Resistance MIL-R-28776/7 (JMGST) 10,000 megohms min. 500 Vdc 1,000 megohms 500 Vdc (coil to case +125C) .014 (0.36) .094 (2.39) DIA FULL R 2 PLS .256 (6.50) .140 .170 W (3.564.32) MGST Mounting Pad Coil Data Coil Nom. Coil Circuit Coil Circuit Pickup Pickup Drop-Out Drop-Out Nom. Coil Resistance Max. Coil Current Current Voltage Voltage Voltage Voltage Power Coil in Ohms Coil Voltage mA (Max.) mA (Min.) Vdc (Max.) Vdc (Max.) Vdc (Min.) Vdc (Min.) (mW) Desig. 10% 25C Voltage (Vdc) (Note) (Note) 25C 125C 25C -65C 25C (Note) MGST 5.0 100 56.0 43.0 2.9 4.0 0.23 0.13 250 5.6 5 6.0 200 33.0 27.0 3.5 4.9 0.32 0.18 180 8.0 6 9.0 400 26.4 17.8 5.3 7.3 0.48 0.27 203 12.0 9 12.0 800 17.7 11.3 7.1 9.8 0.65 0.36 180 16.0 12 18.0 1,600 13.8 8.4 10.6 14.6 0.97 0.54 203 24.0 18 26.5 3,200 10.2 5.8 14.2 19.5 1.30 0.72 219 32.0 26 Note: Coil resistance not directly measurable. Coil current should be within limits shown when tested at nominal voltage at 25C for 5 seconds max. Ordering Instructions Catalog-selected Relays: The catalog number is derived by choosing the proper CODE for each of the relay characteristics in the order in which the codes are listed. Specifying a Part Number Example: Type Terminals Diodes Ground Pins Coils Mounting Pads MGS CT G -26 W * The part number example shown on this page is for catalog items. For a list of specific QPL part numbers, please see the index in Section 15. 1-29 Catalog 5-1773450-5 Dimensions are shown for Dimensions are in millimeters USA: +1 800 522 6752 For additional support numbers Revised 3-13 reference purposes only. unless otherwise specified. Asia Pacific: +86 0 400 820 6015 please visit www.te.com Specifications subject UK: +44 800 267 666 www.te.com to change.