SGRS-3 TE Connectivity

SPECIFICATION CONTROL DRAWING Product Ball Product Dimensions Copper Cross Section Bundle Diameter Name Color A B Min. Max. D L3.5 M1 2 2 max (L0.140) mm (CMA) mm (CMA) (M0.04) 3.6 +0.4/-0.2 SGRS-1 Green 38.3 0.7 (1400) 2.4 (4800) 3.3 15.0 26.02.0 (0.140 +0.016/-0.008) (1.510) (0.130) (0.590) (1.0250.079) SGRS-2 Red 37.7 5.0 +0.7/-0.2 2.0 (4000) 4.0(8000) 4.5 15.0 23.52.0 (1.485) (0.175) (0.590) (0.200 +0.028/-0.008) (0.9250.079) SGRS-3 Blue 45.5 7.5 +0.9/-0.2 3.5 (7000) 8.0(16000) 7.0 15.0 26.52.0 (1.790) (0.295 +0.035/-0.008) (0.275) (0.590) (1.0450.079) SGRS-4 Yellow 45.0 9.4 +0.9/-0.3 7.5 (15000) 12.0(24000) 9.0 15.0 25.53.0 (1.770) (0.370 +0.035/-0.012) (0.350) (0.590) (1.0050.118) These products are tested to RB109. MATERIALS 1. INSULATION SLEEVE: Heat-shrinkable, transparent blue, radiation cross-linked modified polyvinylidene fluoride. 2. SOLDER PREFORM WITH FLUX: SOLDER: TYPE Sn60 per ANSI-J-STD-006. FLUX: TYPE ROM1 per ANSI-J-STD-004. 3. CONICAL SPRING: Square copper wire. 4. END CLOSURE BALL: Tinted glass. Color: see table. 5. SEALING INSERT: Hot melt adhesive. APPLICATION 1. These controlled soldering devices are designed for stub splicing of stranded wires, with bare copper conductors and an insulation rated for 85C minimum and 125C continuous maximum. 2. Temperature range: Class 3, -40C to +125C. 3. Vibration range: Class 1 (body). 4. Seal range: Class 2 (watertight against immersion). Immersion resistant sealing is dependent on the wire combinations used. The user should test specific wire combinations. Refer to TE Connectivity / Raychem Specification RB109 for procedures. 5. For installation procedure and application equipment, consult RPIP-820-00. For best results, prepare the cable as shown: TITLE: TE Connectivity 300 Constitution Drive, SOLDERGRIP DEVICE Raychem Menlo Park, CA. 94025, U.S.A. STUB SPLICE DOCUMENT NO.: Unless otherwise specified dimensions are in millimeters. Inches dimensions are shown in brackets SGRS-X TOLERANCES: ANGLES: N/A TE Connectivity reserves the right to amend 0.00 N/A this drawing at any time. Users should evaluate REV.: DATE: 0.0 N/A ROUGHNESS IN the suitability of the product for their A1 16-Apr-11 0 N/A MICRON application. DRAWN BY: CAGE CODE: REPLACES: DCR NUMBER: SCALE: SIZE: SHEET: P.TALLY 06090 D040187 D060343 NTS A 1 of 1 2011 Tyco Electronics Corporation, a TE Connectivity Ltd. Company. All Rights Reserved. If this document is printed it becomes uncontrolled. Check for the latest revision. Print Date: 9-May-11 X-ON Electronics Largest Supplier of Electrical and Electronic Components Click to view similar products for Solder Sleeves & Shield Tubing category: Click to view products by TE Connectivity manufacturer: Other Similar products are found below : 899170-000 620040N001 620069N003 CTA-0050-01 629624-000 6500750004 6501390002 CX0781-000 696396-000 697080-000 D-150- 0331CS2902 D-181-1222-90/9CS2800 D-300-01CS1108 715325N001 908357N001 982127-1 D-436-0182CS246 D-436-37CS2651 D-436- 61CS246 D-436-82-CS2621 D-659-0087 E53797N001 CB0213-000 CB0219-000 S200-2-01 S200-4-00CS2904 LSS-81-16AA-CS5575 ST18-2-00 FLX40-020-04-CS8651 325534-000 CTA-0025 D-108-07CS436 D-128-0010 D-141-0108CS404 D-144-41CS1371 D-150-0231- NRCS2896 D-150-1011 395947-000 427243N001 B-801-18-01 515-9 C67137-000 CB0220-000 D-436-0185CS1102 D-436-36CS2908 D- 436-37CS2908 D-436-52CS246 D-436-83CS2705 D44133N001 LSS-26-8A