Catalog 1308242 Issued 3-03 (PDF Rev. 4-04) AGASTAT SSC series Specification Grade Discrete Plug-in Time Delay Relay On-Delay, Off-Delay and Interval timing modes 13 timing ranges from 0.1 sec. to 60 min. 10A DPDT output contacts Escellent repeatability of 1% or better. Exceptional immunity to transients and noise. Wide operating temperature range. File LR29186 Users should thoroughly review the technical data before selecting a product part number. It is recommended that user also seek out the pertinent approvals files of the agencies/laboratories and review them to ensure the product meets the requirements for a given application. Input Data 25C Timing Modes On-Delay, Off-Delay and Interval. Voltage: See Ordering Information section for details. Power Requirement: 3W, max. Transient Protection: Non-repetitive transients of the following magni- Timing Specifications tudes will not cause spurious operation of affect function and accuracy. Timing Ranges: 6 to 180 cycles 0.1 to 3 / 0.1 to 10 / 0.33 to 10 / 1 to 30 / 4 Operating Voltage <0.1 ms <1 ms to 120 sec. 0.33 to 10 / 1 to 30 / 2 to 60 min. 0.33 to 10 12VDC 1,000V 240V* hr. (All are +10%, 1% of maximum values). 24VAC/VDC 1,000V 240V* Timing Adjustment: Knob or fixed time (internal fixed resistor) all models 48 VAC/VDC 1,000V 480V* customer supplied external potentiometer or resistor 120 VAC/VDC 3,000V 2,500V* On-Delay and Interval models only. 240VAC 3,000V 2,500V* Accuracy: Repeat Accuracy: 1% 0.004 sec. at any combination of operating temperature and voltage. * Minimum source impedance of 100 ohm. Overall Accuracy: 5.25% throughout operating temperature and voltage ranges. Environmental Data Reset Time: 25 ms. (minimum deenergized interval for on-delay or off-delay Temperature Range: Storage: -40C to +85C. models, or minimum required closure interval for interval Operating: -30C to +65C. models without affecting accuracy.) Relay Operate Time: Off-Delay mode only: 35 ms. Mechanical Data Relay Release Time: On-Delay mode only: 20 ms. Mounting/Termination: 8- or 11-pin octal type plug. 8-pin types fit either 27E122 or 27E891, while 11-pin types fit 27E123 or 27E892. Contact Data 25C Weight: 4 oz. (112g) approximately. Arrangements: 2 Form C (DPDT). Rating: 10A 28VDC or 120VAC, resistive 1/3 HP 120/240VAC. Ordering Information Expected Mechanical Life: 10 million operations. 01 SSC 2 A A A Expected Electrical Life: 500,000 operations, min., at rated resistive load. Initial Dielectric Strength Series SSC Output Timing Range Between Terminals and Case: 1,000VAC plus twice the nominal voltage Discrete 2 = DPDT Relay A =0 .1 to 3 sec. for one minute. Industrial B = 0.5 to 15 sec. Timer C = 1 to 30 sec. Outline Dimensions D = 2 to 60 sec. Operating Mode E = 4 to 120 sec. 1.97 .70 3.25 (50) (18) (83) 01 = On-Delay F = 6 to 180 sec. 02 = Off-Delay G = 10 to 300 sec. 03 = Interval I = 2 to 60 min. 1.97 K = 3 to 180 cycles (50) L = 0.33 to 10 min. M = 0.5 to 15 min. N = 1 to 30 min. P = 0.1 to 10 min. Wiring Diagrams (Bottom Views) Operating Voltage Timing Adjustment Insulated, shielded two- (+10%, 15%) A = Knob Adjust conductor cable similar to Belden 8719, 8720 or A = 120VAC, 50/60 Hz. B = External 8769 required for leads / 120VDC Potentiometer or longer than 6 inches. B = 240VAC, 50/60 Hz. resistor (Operating Max. permissble length is 50 feet. E = 24VAC, 50/60 Hz. / modes 1 and 3 only). 24VDC F = Fixed Times F = 48VAC, 50/60 Hz. / Specify time delay 48VDC in seconds per the Q = 12VDC (10%) following examples: F9.000 = 9 sec. F99.00 = 99 sec. F999.0 = 9999 sec. F1000 = 1000 sec. Off-Delay On-Delay & Interval On-Delay & Interval Authorized distributors are likely to stock the following: Fixed or Knob Fixed or Knob External Potentiomer SSC12AAA SSC12ACA SSC12AGA Adjust Adjust or Resistor Adjust SSC12ABA SSC12ADA SSC12ALA. Dimensions are shown for Dimensions are in inches over Specifications and availability www.tycoelectronics.com reference purposes only. (millimeters) unless otherwise subject to change. Technical support: 1234 specified. Refer to inside back cover.