T9ES1D22-12 TE Connectivity

General Purpose High Power PCB Relays Potter & Brumfield Power PCB Relay T9E n 1 pole 30A, 1 formA(NO) or 1 formC(CO) n High breaking capacity 7500 VA n PCB and PCB/quick connect terminals n UL class F insulation as standard n Ambient temperature up to 105C n Plastic materials according to IEC60335-1 Typical applications HVAC, power supplies, domestic appliances, measurement and control. Approvals Coil Data (continued) VDE 40027903, UL E58304 Technical data of approved types on request. Coil versions, DC coil Coil Rated Operate Release Coil Rated coil Contact Data code voltage voltage voltage resistance power Contact arrangement 1 form A (NO) 1 form C (CO) VDC VDC VDC 10% W Rated voltage 240VAC Code D (1W) coil Max. switching voltage 250VAC (VDE) 300VAC (UL) 6 6 4.5 0.6 36 1 Rated current 30A 20A/10A 9 9 6.75 0.9 81 1 Limiting continuous current 30A 12 12 9 1.2 144 1 Breaking capacity max. 7500VA 5000/2500VA 18 18 13.5 1.8 324 1 Contact material AgSnOInO (AgCdO optional) 22 22 16.5 2.2 484 1 Min. recommended contact load 1A, 5VDC or 12VAC 24 24 18 2.4 576 1 Initial contact resistance 75 m at 1A at 5VDC or 12VAC 48 48 36.2 4.8 2304 1 -1 Frequency of operation, with/without load 6/120min 110 110 82.5 11 12100 1 Operate/release time max., including bounce 15/15ms Code L (900mW) coil 6 6 4.5 0.6 40 .9 Contact ratings 12 12 9 1.2 155 .9 Type Contact Load Cycles 18 18 13.5 1.8 380 .9 IEC 61810 24 24 18 2.4 660 .9 AgSnOInO, 1W coil All figures are given for coil without preenergization, at ambient temperature +23C. 3 1 NO 30A, 250VAC, cosj=1, 60C 20x10 3 1 NO 20A, 250VAC, cosj=1, 85C 100x10 3 2 NO 20A, 250VAC, cosj=1, 70C 100x10 Insulation Data 3 1, 2 CO 20A / 10A, 250VAC, cosj=1, 60C 20x10 Initial dielectric strength AgSnOInO, 900mW coil between open contacts 1500V rms 3 1 NO 17A, 250VAC, cosj=1, 105C 100x10 between contact and coil 2500V rms 3 1 NO 20A, 250VAC, cosj=1, 85C 100x10 Initial surge withstand voltage EN 60730-1 between contact and coil 6kV (1.2s/50s impulse wave) AgSnOInO, 1W coil Initial insulation resistance 3 9 1 NO 12(12)A, 240VAC, 60C 100x10 between insulated elements 1x10 UL 508 1) Clearance/creepage AgSnOInO, 1W coil between contact and coil 3mm/4mm 3 1, 2 NO 30A, 240VAC, general purpose, 25C 100x10 AgSnOInO, 900mW coil 3 1, 2 NO TV-8, 125VAC, 25C 25x10 1) Additional UL 508 ratings are available. 6 Mechanical endurance 10x10 ops. Coil Data Coil voltage range 6 to 110VDC Max. coil power 110% of nominal Max. coil temperature 155C Coil insulation system according UL Class F Coil operating ranges shown above are for 1W coils. 1 02-2014, Rev. 0214 Catalog and product specification according Catalog and product data is subject to the Catalog product data, Definitions section, www.te.com to IEC 61810-1 and to be used only together terms of the disclaimer and all chapters of application notes and all specifications are 2014 Tyco Electronics Corporation, with the Definitions section. the Definitions section, available at subject to change. a TE Connectivity Ltd. company. General Purpose High Power PCB Relays PPottotter & Brumfielder & Brumfield Power PCB Relay T9E (Continued) Other Data Other Data (Continued) Material compliance: EU RoHS/ELV, China RoHS, REACH, Halogen content Terminal type PCB-tht and PCB-tht + quick refer to the Product Compliance Support Center at connect www.te.com/customersupport/rohssupportcenter Weight 26g mounting code 1 Ambient temperature 33g mounting codes 2 and 5 DC coil -40C to 85C / 105C Resistance to soldering heat THT Category of environmental protection IEC 60068-2-20 260C IEC 61810 RTII - flux proof (T9EV) Packaging/unit tray/50 pcs., box/250 pcs. RTIII - wash tight (T9ES) Vibration resistance (functional) 1.5mm, 10-55 Hz Shock resistance (functional) 10g for 11msec Shock resistance (destructive) 100g Dimensions PCB version PCB/quick connect version 27,4 MAX. 27,4 MAX. S0290-A S0289-A +,41 3,3 ,25 Terminal assignment Bottom view on pins 1 form A 1 form C PCB layout Bottom view on pins PCB version PCB/quick connect version Only necessary terminals are Only necessary terminals are present on single throw models. present on single throw models. Consequently, some holes will Consequently, some holes will be unnecessary for single throw be unnecessary for single throw models. models. S0261-AH S0261-AA 2 02-2014, Rev. 0214 Catalog and product specification according Catalog and product data is subject to the Catalog product data, Definitions section, www.te.com to IEC 61810-1 and to be used only together terms of the disclaimer and all chapters of application notes and all specifications are 2014 Tyco Electronics Corporation, with the Definitions section. the Definitions section, available at subject to change. a TE Connectivity Ltd. company.