T9GS2L24-24 TE Connectivity

General Purpose Relays Power Relays Potter & Brumfield T9G series, DC coil 30A PCB Relay n 30A switching in NO and 20A in CO n Minimum Board space (29mm x 21.5mm) n Meets UL 508 for clearance / creepage n Meets IEC 61810-1 for reinforced insulation n Option for load connections via 0.250 (6.3mm) quick connect terminals n 4kV dielectric withstand and 8kV surge voltage between coil & contacts n UL approved for 480 VAC switching Typical applications HVAC, Appliances, Industrial Controls, Energy Management Approvals UL 508 UL Listing E214025 1) IEC 61810-1 VDE Listing 40045012 Contact ratings (continued) Technical data of approved types on request Type Load Cycles 3 CO 20A, 250VAC, Resistive 15x10 3 Contact Data CO 20A /10A, 240VAC, Resistive 100x10 3 Contact arrangement 1 form A (NO), 1 form B (NC), 1 form C (CO) CO 30A / 15A Resistive, 250VAC 20x10 3 Rated voltage 250VAC CO 30A FLA / 80A LRA (N.O.) 12A FLA, 30A LRA 30x10 Max. switching voltage 480VAC (N.C.) 250VAC, Definite Purpose 3 Rated current 30A 20A 20A CO 80A LRA / 10A FLA (N.O.) 33A LRA / 10A FLA 30x10 Contact material AgSnO (N.C.) 250VAC, Definite Purpose Min. recommended contact load 1A, 12VAC/VDC IEC 61810-1 Initial contact resistance 300m at 100mA/6VDC Type Load Cycles 3 Frequency of operation, with/without load 360 cycles / hour = with NO 30A, 250VAC, Resistive, 85C (PCB) 75x10 3 3600 cycles / hour = without NO 20A, 250VAC, Resistive, 70C (QC), 85C (PCB) 100x10 3 Operate/release time max., including bounce 15/22ms NO 17A, 250VAC, Resistive, 105C 100x10 3 NO 20A, 250VAC, Resistive, 85C 100x10 1) 3 Contact ratings NO 12A (12A), 250VAC, 60C (per EN60730-1) 150x10 UL 508 3 Type Load Cycles NC 10A, 250VAC, Resistive, 60C (C.O. type only) 50x10 3 NO 5A, 480VAC, General Purpose 6x10 3 3 NO 15,6A, 480VAC, Resistive 100x10 CO 20A, 250VAC, Resistive, 60C (N.C.) 10x10 3 3 NO 30A, 277VAC, General Purpose, 85C 100x10 CO 20A/10A, 250VAC, Resistive, 60C (N.O.) 50x10 3 3 NO 18A, 250VAC, Resistive, 105C 100x10 CO 12A , 250VAC, Resistive, 85C 100x10 3 NO 22A, 250VAC, Resistive 250x10 3 NO 22A FLA, 98A LRA, 120VAC, Definite Purpose 100x10 1) Contact ratings at 40C (unless otherwise noted) with relay properly vented. Remove vent nib after soldering and cleaning. NO 14A FLA, 82A LRA, 250VAC, Definite Purpose, 70C 3 30x10 3 6 NO 20A, 277VAC, Standard Ballast 6x10 Mechanical endurance 10x10 ops. 3 NO 1HP, 125VAC 100x10 3 NC 15A, 240VAC, General Purpose 100x10 Coil Data 3 NC 20A, 250VAC, Resistive (CO type only) 20x10 Coil voltage range 5 to 110VDC 3 NC 30A LRA / 12A FLA, 250VAC, Definite Purpose 30x10 Max. coil power 110% of nominal 3 NC 1HP, 277VAC (CO type only) 50x10 Max. coil temperature 155C Coil insulation system according UL Class F Coil versions, DC coil Coil Rated Operate Release Coil Rated coil code voltage voltage voltage resistance power VDC VDC VDC 10% mW 5 5 3.75 0.5 28 900 9 9 6.75 0.9 90 900 12 12 9 1.2 160 900 15 15 11.25 1.5 249 900 18 18 13.5 1.8 360 900 22 22 16.5 2.2 538 900 24 24 18 2.4 640 900 48 48 36 4.8 2,560 900 110 110 82.5 11 13,444 900 All figures are given for coil without preenergization, at ambient temperature +23C. 1) Contact ratings at 40C (unless otherwise noted) with relay properly vented. Remove vent nib after soldering and cleaning. 1 11-2017, Rev. 1117 Datasheets and product specification Datasheets and product data is subject to the Datasheets, product data, Definitions sec - www.te.com according to IEC 61810-1 and to be used terms of the disclaimer and all chapters of tion, application notes and all specifications 2017 Tyco Electronics Corporation, only together with the Definitions section. the Definitions section, available at are subject to change. a TE Connectivity Ltd. company General Purpose Relays Power Relays Potter & Brumfield T9G series, DC coil 30A PCB Relay (Continued) Coil Data (continued) Insulation Data Initial dielectric strength between open contacts 1500V rms between contact and coil 4000V rms Initial surge withstand voltage between contact and coil 8kV Initial insulation resistance 9 between insulated elements 1x10 , 500VDC Clearance/creepage between contact and coil 6.4mm / 9.5mm (UL), 8mm / 8mm (IEC) Other Data Material compliance: EU RoHS/ELV, China RoHS, REACH, Halogen content refer to the Product Compliance Support Center at www.te.com/customersupport/rohssupportcenter Ambient temperature DC coil Storage -55C to +130C Operating -40 to + 105C at reduced current Category of environmental protection IEC 61810 RTII - flux proof RTIII - wash tight Vibration resistance (functional) Opening NO contact >10g Opening NC contact >7g Shock resistance (functional) 10g for 11msec Shock resistance (destructive) 100g Terminal type pcb-tht and pcb-tht + quick connect Weight 18g mounting code 1 23g mounting code 2 Resistance to soldering heat THT IEC 60068-2-20 250C Packaging/unit 10/tube, 420/box (PCB + QC), 500/box (PCB) PCB layout Bottom view on pins T9G - Mounting and termination code 1 T9G - Mounting and termination code 2 Only necessary terminals are Only necessary terminals are present on single throw models. present on single throw models. Consequently, some holes will Consequently, some holes will be unnecessary for single throw be unnecessary for single throw models. models. 2 11-2017, Rev. 1117 Datasheets and product specification Datasheets and product data is subject to the Datasheets, product data, Definitions sec - www.te.com according to IEC 61810-1 and to be used terms of the disclaimer and all chapters of tion, application notes and all specifications 2017 Tyco Electronics Corporation, only together with the Definitions section. the Definitions section, available at are subject to change. a TE Connectivity Ltd. company