T9GV1L24-22 TE Connectivity

General Purpose Relays Power Relays Potter & Brumfield T9G series, DC coil 30A PCB Relay Typical applications HVAC, Appliances, Industrial Controls, Energy Management Approvals IEC 61810-1 UL 508 UL Listing E214025 Type Load Cycles 3 IEC 61810-1 VDE Listing 40045012 NO 30A, 250VAC, Resistive, 85C (PCB) 75x10 3 CQC 18002196927 (only for standard version in preparation for WG NO 20A, 250VAC, Resistive, 70C (QC), 85C (PCB) 100x10 3 version) NO 17A, 250VAC, Resistive, 105C 100x10 3 Technical data of approved types on request NO 20A, 250VAC, Resistive, 85C 100x10 3 NO 12A (12A), 250VAC, 60C (per EN60730-1) 150x10 Contact Data 3 Contact arrangement 1 form A (NO), 1 form B (NC), 1 form C (CO) NC 10A, 250VAC, Resistive, 60C (C.O. type only) 50x10 Rated voltage 250VAC 3 Max. switching voltage 480VAC CO 20A, 250VAC, Resistive, 60C (N.C.) 10x10 3 Rated current 30A 20A 20A CO 20A/10A, 250VAC, Resistive, 60C (N.O.) 50x10 3 Contact material AgSnO CO 12A , 250VAC, Resistive, 85C 100x10 Min. recommended contact load 1A, 12VAC/VDC 1) Contact ratings at 40C (unless otherwise noted) with relay properly vented. Initial contact resistance 300m at 100mA/6VDC Remove vent nib after soldering and cleaning. Frequency of operation, with/without load 360 cycles / hour = with 2) Valid only for mounting and termination code 1. 3600 cycles / hour = without Operate/release time max., including bounce 15/22ms 6 Mechanical endurance 10x10 ops. 1) Contact ratings UL 508 Type Load Cycles Coil Data 3 NO 5A, 480VAC, General Purpose 6x10 Coil voltage range 5 to 110VDC 3 NO 15,6A, 480VAC, Resistive 100x10 Operative range, IEC 61810 2 3 NO 30A, 277VAC, General Purpose, 85C 100x10 Coil insulation system according UL Class F 3 NO 18A, 250VAC, Resistive, 105C 100x10 Coil versions, DC coil 3 NO 22A, 250VAC, Resistive 250x10 Coil Rated Operate Release Coil Rated coil 3 NO 22A FLA, 98A LRA, 120VAC, Def. Purpose 100x10 code voltage voltage voltage resistance power 3 NO 14A FLA, 82A LRA, 250VAC, Def. Purpose, 70C 30x10 VDC VDC VDC 10% mW 3 NO 20A, 277VAC, Standard Ballast 6x10 5 5 3.75 0.5 28 900 3 NO 1HP, 125VAC 100x10 9 9 6.75 0.9 90 900 2) 3 NO 40A, 277VAC, Resistive 6x10 12 12 9 1.2 160 900 2) 3 NO TV8, 240VAC 25x10 15 15 11.25 1.5 249 900 18 18 13.5 1.8 360 900 3 NC 15A, 240VAC, General Purpose 100x10 22 22 16.5 2.2 538 900 3 NC 20A, 250VAC, Resistive (CO type only) 20x10 24 24 18 2.4 640 900 3 NC 30A LRA / 12A FLA, 250VAC, Definite Purpose 30x10 48 48 36 4.8 2,560 900 3 NC 1HP, 277VAC (CO type only) 50x10 110 110 82.5 11 13,444 900 All figures are given for coil without preenergization, at ambient temperature +23C. 3 CO 20A, 250VAC, Resistive 15x10 3 CO 20A /10A, 240VAC, Resistive 100x10 3 CO 30A / 15A Resistive, 250VAC 20x10 3 CO 30A FLA / 80A LRA (N.O.) 12A FLA, 30A LRA 30x10 (N.C.) 250VAC, Definite Purpose 3 CO 80A LRA / 10A FLA (N.O.) 33A LRA / 10A FLA 30x10 (N.C.) 250VAC, Definite Purpose 1 03-2021, Rev. 0321 Datasheets and product specification Datasheets and product data is subject to the Datasheets, product data, Definitions sec - www.te.com according to IEC 61810-1 and to be used terms of the disclaimer and all chapters of tion, application notes and all specifications 2017 Tyco Electronics Corporation, only together with the Definitions section. the Definitions section, available at are subject to change. a TE Connectivity Ltd. company General Purpose Relays Power Relays Potter & Brumfield T9G series, DC coil 30A PCB Relay (Continued) Coil Data (continued) Insulation Data Initial dielectric strength between open contacts 1500V rms between contact and coil 4000V rms Initial surge withstand voltage between contact and coil 8kV Initial insulation resistance 9 between insulated elements 1x10 , 500VDC Clearance/creepage between contact and coil >6.4mm / >8mm Other Data Material compliance: EU RoHS/ELV, China RoHS, REACH, Halogen content refer to the Product Compliance Support Center at www.te.com/customersupport/rohssupportcenter Ambient temperature DC coil Operating -40 to + 105C at reduced current Category of environmental protection IEC 61810 RTII - flux proof RTIII - wash tight Vibration resistance (functional) Opening NO contact >10g Opening NC contact >7g Shock resistance (functional) 10g for 11msec Shock resistance (destructive) 100g Terminal type pcb-tht and pcb-tht + quick connect Weight 18g mounting code 1 23g mounting code 2 Resistance to soldering heat THT IEC 60068-2-20 260C/5s Packaging/unit 10/tube, 420/box (PCB + QC), 500/box (PCB) PCB layout Bottom view on pins T9G - Mounting and termination code 1 T9G - Mounting and termination code 2 Only necessary terminals are Only necessary terminals are present on single throw models. present on single throw models. Consequently, some holes will Consequently, some holes will be unnecessary for single throw be unnecessary for single throw models. models. 2 03-2021, Rev. 0321 Datasheets and product specification Datasheets and product data is subject to the Datasheets, product data, Definitions sec - www.te.com according to IEC 61810-1 and to be used terms of the disclaimer and all chapters of tion, application notes and all specifications 2017 Tyco Electronics Corporation, only together with the Definitions section. the Definitions section, available at are subject to change. a TE Connectivity Ltd. company