TE120B220RJ TE Connectivity

High Power Wire Wound Resistor Type TE Series Key Features Up to 2500W Power rating in free air Flameproof construction UL94V coating RoHS compliant Custom terminations / leads available Applications Large electrical TE Connectivity is a leading supplier of standard and custom-designed power and production resistors for industrial, control and general- purpose applications. machinery The TE range of flameproof coated tubular ceramic core resistors use both Load test standard and edge wound (corrugated) winding methods to improve power simulation handling capability. Designed for heavy duty machinery, electrical equipment, Motor start / motor control etc. requiring stability and reliability. stop cycles Dynamic braking Characteristics Electrical Equipment discharge 50W 2500W (see table) Power rating 70C in free air See table Resistance range E12 Selection series 5% 10% Tolerance < PPM/C Temperature Coefficient of 300PPM/C resistance -55 ~ +155C Operating temperature range 3 x rated power / 5 seconds Short term overload 2500VAC Min. Dielectric strength DCV M min. Insulation resistance Dimensions in Dimensions Shown for 9-1773453-2 CIS WR 12/2016 For Email, phone or live chat, millimetres unless reference purposes only. go to: www.te.com/help otherwise specified Specifications subject to change High Power Wire Wound Resistor Specifications Electrical Power Resistance Tolerance Dielectric Appearance Rating Value Strength 50W R10 ~ 2K7 5% 10% 500VAC Smooth 60W R10 ~ 2K7 5% 10% 500VAC Smooth 80W R10 ~ 2K7 5% 10% 500VAC Smooth 100W 1R0 ~ 2K7 5% 10% 500VAC Smooth 120W 1R0 ~ 2K7 5% 10% 500VAC Smooth 150W 1R0 ~ 2K7 5% 10% 500VAC Smooth 1R0 ~ 9R1 5% 10% 300VAC Ribbed 200W 10R ~ 2K7 5% 10% 500VAC Smooth 1R0 ~ 9R1 5% 10% 300VAC Ribbed 300W 10R ~ 2K7 5% 10% 500VAC Smooth 1R0 ~ 15R 5% 10% 300VAC Ribbed 400W 16R ~ 2K7 5% 10% 500VAC Smooth 1R0 ~ 20R 5% 10% 300VAC Ribbed 500W 21R ~ 2K7 5% 10% 500VAC Smooth 1R0 ~ 20R 5% 10% 300VAC Ribbed 600W 21R ~ 2K7 5% 10% 500VAC Smooth 1R0 ~ 75R 5% 10% 300VAC Ribbed 750W 76R ~ 2K7 5% 10% 500VAC Smooth 1R0 ~ 100R 5% 10% 300VAC Ribbed 1000W 101R ~ 2K7 5% 10% 500VAC Smooth 1R0 ~ 100R 5% 10% 300VAC Ribbed 1200W 101R ~ 2K7 5% 10% 500VAC Smooth 1R0 ~ 120R 5% 10% 300VAC Ribbed 1500W 121R ~ 2K7 5% 10% 500VAC Smooth 1R0 ~ 120R 5% 10% 300VAC Ribbed 2000W 121R ~ 2K7 5% 10% 500VAC Smooth 1R0 ~ 120R 5% 10% 300VAC Ribbed 2500W 121R ~ 2K7 5% 10% 500VAC Smooth Voltage rating: Resistors shall have a rated direct-current (DC) continuous working voltage or an approximate sine-wave root-mean-square (RMS) alternating-current (AC) continuous working voltage at commercial line frequency and waveform corresponding to the power rating, as determined from the following formula: RCWV = P x R Where : RCWV = Rated DC or RMS AC continuous working voltage at commercial-line frequency and waveform (volt) P = Power Rating (watt) R = Nominal Resistance (ohm) Dimensions in Dimensions Shown for 9-1773453-2 CIS WR 12/2016 For Email, phone or live chat, millimetres unless reference purposes only. go to: www.te.com/help otherwise specified Specifications subject to change