Automotive Relays PCB Single Relays Power Relay K (Sealed) Limiting continuous current 45A Wide voltage range Typical applications ABS control, blower fans, car alarm, cooling fan, engine control, fuel pump, hazard warning signal, heated front screen, heated rear screen, ignition, lamps front/rear/fog light, interior lights, main switch/supply relay, seat control, seatbelt pretensioner, sun roof, turn signal, valves, window lifter, F076 fcw2b wiper control. Contact Data Coil Data Typical applications Resistive/inductive Headlights Rated coil voltage 12VDC loads capacitive loads Contact arrangement 1 form C, 1 CO Coil versions, DC coil Rated voltage 12VDC 12VDC Coil Rated Operate Release Coil Rated coil A/B (NO/NC) code voltage voltage voltage resistance power VDC VDC VDC 10% W Rated current 45/30A 40/25A 1) Limiting continuous current 001 12 6.9 1.2 90 1.6 All gures are given for coil without pre-energization, at ambient temperature +23C. 23C 45/30A 40/25A Other coils on request. 85C 30/25A 25/20A 2) Limiting making current 100/30A 180/60A 3) Limiting breaking current 60/30A 60/30A Insulation Data Contact material AgNi0.15 SgSnO Initial dielectric strength 2 4) Min. recommended contact load 1A at 5VDC between open contacts 500VAC rms Initial voltage drop, at 10A, typ./max. 20/300mV between contact and coil 500VAC rms 5) Operate/release time typ. 5/3ms 5 5 Electrical endurance >2x10 ops. >10 ops. at 13.5VDC, 40A up to 4x60W Other Data 7 Mechanical endurance, DC coil >10 ops. EU RoHS/ELV compliance compliant 2 6) 1) Measured on 70x70x1.5mm epoxy PCB FR4 with 35cm (double layer 105m) copper Ambient temperature, DC coil -40 to +85C area. Cable cross section 6mm. Boundary conditions: 180C coil temperature 130C Climatic cycling with condensation, solder joint. Solder joint results above 130C on request. The load circuit shall withstand EN ISO 6988 3 cycles, storage 8/16h current applied on 40A MAXI fuse. Temperature cycling (shock), 2) The values apply to a resistive or inductive load with suitable spark suppression and at IEC 60068-2-14, Na 20 cycles, -40/+85C (dwell time 1h) maximum 13.5VDC load voltages. Damp heat cyclic, 3) For a load current duration of maximum 3s for a make/break ratio of 1:10. 4) See chapter Diagnostics of Relays in our Application Notes or consult the internet at IEC 60068-2-30, Db, Variant 1 6 cycles, upper air temperature 55C 13.3 0.2 Automotive Relays PCB Single Relays Power Relay K (Sealed) (Continued) Terminal Assignment Other Data (continued) Bottom view on solder pins Damp heat constant, 56 days, upper air temperature 55C IEC 60068-2-3, method Ca RT III immersion cleanable version 1 form C, 1 CO Corrosive gas, IEC 60068-2-42 10 days IEC 60068-2-43 10 days Vibration resistance (functional), IEC 60068-2-6 (sine pulse form), 7) acceleration, acc. to position 10 to 200Hz, 20 to 40g Shock resistance (functional), IEC 60068-2-27 (half sine form single pulses), 7) acceleration, acc. to position 8ms 30g TE1086-A1 Terminal type PCB Weight sealed version approx. 22g (0.77oz) open version approx. 19g (0.67oz) Solderability (aging 3: 4h/155C) for leaded process (Tm = 183C), for Pb-free process (Tm = 217C), IEC 60068-2-20 Ta, method 1, hot dip 5s, 215C 8) Storage conditions according IEC 600688 Packaging unit sealed version 525 pcs. 6) See coil operating range DC. 7) No change in the switching state >10s. 8) For general storage and processing recommendations please refer to our Application Notes and especially to Storage in the Denitions or at