Signal Relays
AXICOM
P2 Relay V23079
n
Standard telecom relay (ringing and test access)
n
Slim line 15x7.5mm (.590x.295)
n
Max. switching current 5A
n
2 form C bifurcated contacts (2 changeover contacts, 2 CO)
n
Immersion cleanable
n
High sensitivity for low power consumption 140mW/ 70mW
n
Single coil version with surge voltage resistance between contact
and coil: 2.5kV (2/10s) meets the Telcordia Requirement GR-1089,
1.5kV (10/160s) meets FCC Part 68
AXICOM
Typical applications
Telecom-, Signal and RF Relays 108-98002 Rev. E
Communications equipment linecard application (ringing and test access),
PABX, voice over IP, office equipment, measurement and control equipment,
P2 V23079 Relay
automotive equipment as CAN bus, keyless entry, speaker switch, medical
Z
equipment, consumer electronics, set top boxes, HiFi
Coil Operating Range
Approvals Coil Data
UL 508 File No. E 111441, UL 60950, Magnetic system polarized
3.4
IEC/EN60950 IEC Ref. Cert. No. 327 Coil voltage range 2 to 24VDC70 mW
U = Nominal coil voltage
3.2
nom
Technical data of approved types on request Max. coil temperature 125C
3
Umax. at 0 A
Thermal resistance2.8 < 125K/W
U = Upper limit of the operative range of
Umax. at 2 x 1 A
max.
2.6
Contact Data Umax. at 2 x 2 A
the coil voltage (limiting voltage) when coils are
2.4
Contact arrangement 2 form C (CO) Coil versions, monostable
2.2
continously energized
Max. switching voltage 220VDC, 250VAC Coil Rated Operate Limiting Release Coil Rated coil
2
Rated current 2A code voltage voltage Voltage voltage resistance power
1.8
U = Lower limit of the operative range of
op. min.
Limiting continuous current, 85C 2A VDC VDC VDC VDC 10% mW
1.6
the coil voltage (reliable operate voltage)
1.4
Switching Power 60W, 62.5VA 008 3.00 2.25 6.50 0.30 64 140
1.2
Contact material AgNi, gold-covered 016 4.00 3.00 8.70 0.40 114 140
Unom. nominal coil voltage
1
For latching relays U resp. U
set min. reset min.
Contact style bifurcated contact 011 4.50 3.38 9.80 0.45 145 140
0.8
Minimum switching voltage 100V 001 5.00 3.75 10.90 0.50 178 140
Uop. min.
0.6
U = Lower limit of the operative range of
rel. min.
Thermoelectrical potential <10V 002 6.00 4.50 13.00 0.60 257 140
0.4
the coil voltage (reliable release voltage)
Initial contact resistance <50m at 10mA, 20mV 006 0.29.00 6.75 19.60 0.90 578 140
0
Frequency of operation, without load 50 operations/s 003 12.00 9.00 26.15 1.20 1029 140
-40-30 -20-10 0102030405060708090 100 110 120 130 140
Operate time typ. 2ms, max. 4ms 005 24.00 18.00 52.30 2.40 4114 140
Ambient Temperature [C]
Set/reset time typ. 2ms, max. 4ms All figures are given for coil without pre-energization, at ambient temperature +23C.
Other coil voltages on request.
Release time
without diode in parallel typ. 2ms, max. 4ms
2.8
with diode in parallel typ. 4ms, max. 6ms 140 mW
2.6
Bounce time typ. 1ms, max. 3ms
Umax. at 0 A
2.4 Umax. at 2 x 1 A
Electrical endurance
7 Umax. at 2 x 2 A
2.2
at 12V / 10mA typ. 5x10 operations
7
2
at 6V / 100mA typ. 1x10 operations
5
1.8
at 60V / 500mA typ. 5x10 operations
6
1.6
at 30V / 1000mA typ. 1x10 operations
5
1.4
at 30V / 2000mA typ. 2x10 operations
1.2
Contact ratings, UL 110VDC / 0.3A - 33W
Unom. nominal coil voltage
1
30VDC / 2.0A - 60W
0.8
120VAC / 0.5A - 60VA
0.6
240VAC / 0.25A -60VA
Uop. min.
6
0.4
Mechanical endurance typ. 100x10 operations
Urel. min.
0.2
Max. DC load breaking capacity
0
-40-30 -20-10 0102030405060708090 100 110 120 130 140
Ambient Temperature [C]
200 mW
2.8
2.6
Umax. at 0 A
Umax. at 2 x 1 A
2.4
Umax. at 2 x 2 A
2.2
2
1.8
1.6
1.4
1.2
Unom. nominal coil voltage
1
0.8
DC current [A]
0.6
1
Uop. min.
10-2014, Rev.1014 Datasheets and product specification Datasheets and product da0.4 ta is subject to the Datasheets, product data, Definitions sec-
Urel. min.
www.te.com according to IEC 61810-1 and to be used terms of the disclaimer and all chapters of tion, application notes and all specifications
0.2
2014 Tyco Electronics Corporation, only together with the Definitions section. the Definitions section, available at are subject to change.
0
-40-30 -20-10 0102030405060708090 100 110 120 130 140
a TE Connectivity Ltd. company Signal Relays
AXICOM
P2 Relay V23079 (Continued)
Coil Data (continued) Insulation Data Standard HDV
Initial dielectric strength
Coil versions, bistable between open contacts 1000V 1500V
rms rms
Coil Rated Set Limiting Reset Coil Rated coil between contact and coil 1500V 1500V
rms rms
code voltage voltage Voltage voltage resistance power between adjacent contacts 1000 V 1500V
rms rms
VDC VDC VDC VDC 10% mW Initial surge withstand voltage
Bistable, 1 coil according to Telcordia TR-NWT-001089 (2/10s)
AXICOM
108 3.00 2.25 9.2 -2.25 128 70 between open contacts 2000V 2500V
Telecom-, Signal and RF Relays 108-98002 Rev. E
111 4.50 3.38 13.85 -3.38 289 70 between contact and coil 2500V 2500V
101 5.00 3.75 15.33 -3.75 357 70 between adjacent contacts 2500V 2500V
P2 V23079 Relay
102 6.00 4.50 18.5 -4.50 514 70 according to (10/700 s IEC 60950)
106 9.00 6.75 27.75 -6.75 1157 70 between open contacts 2000V 2500V
103 12.00 9.00 37 -9.00 2057 70 between contact and coil 2500V 2500V
105 Coil Ope24.00 ra18.00ting Range 74 -18.00 8228 70 between adjacent contacts 2500V 2500V
9
Bistable, 2 coil Initial insulation resistance at 500 Vdc > 10
219 2.00 1.50 4.33 1.50 28 140 Capacitance
3.4
218 2.40 1.80 5.2 1.80 41 140 between open contacts max. 1pF
70 mW
AXICOM
U = Nominal coil voltage
3.2
nom
208 3.00 2.25 6.5 2.25 64 140 between contact and coil max. 2pF
Telecom-, Signal and RF Relays
108-98002 Rev. E
3
Umax. at 0 A
211 4.50 3.38 9.8 3.38 145 140 between adjacent contacts max. 1.5pF
2.8
U = Upper limit of the operative range of
Umax. at 2 x 1 A
max.
201 5.00 3.75 10.9 3.75 178 140 Clearance /creepage
2.6
Umax. at 2 x 2 A
P2 V23079 Relay
the coil voltage (limiting voltage) when coils are
202 2.6.004 4.50 13 4.50 257 140 according to IEC / EN 60950 1.3/2.5mm
2.2
continously energized
206 9.00 6.75 19.6 6.75 578 140
2
203 12.00 9.00 26.15 9.00 1029 140
1.8
U = Lower limit of the operative range of
205 Coil Ope24.00 ra18.00ting Range 52.3 18.00 4114 140 op. min.Other Data
1.6
All figures are given for coil without pre-energization, at ambient temperature +23C. the coil voltage (reliable operate voltage)
1.4 Material compliance: EU RoHS/ELV, China RoHS, REACH, Halogen content
Other coil voltages on request.
1.2
refer to the Product Compliance Support Center at
Unom. nominal coil voltage
3.14
For latching relays U resp. U
wwwset min..te.com/customersupport/rreset min. ohssupportcenter
70 mW
U = Nominal coil voltage
3.0.28 nom
Ambient temperature -40 to +85C
Uop. min.
3
0.6
Umax. at 0 A
U = Lower limit of the operative range of
rel. min.
Category of environmental protection
2.0.84
Umax. at 2 x 1 A U = Upper limit of the operative range of
max.
2.6 IEC 61810the coil voltage (reliable release voltage) RT III - wash tight
0.2
Umax. at 2 x 2 A
the coil voltage (limiting voltage) when coils are
2.04
Degree of protection, IEC 60529 IP 67
-40-30 -20-10 0102030405060708090 100 110 120 130 140
2.2
continously energized
Vibration resistance (functional) 35g, 10 to 1000Hz
2 Ambient Temperature [C]
Shock resistance (functional)
1.8
U = Lower limit of the operative range of
op. min.
IEC 60068-2-27 (half sine) 100g
1.6
Terminal typethe coil voltage (reliable operate voltage) PCB-THT,
1.4
1.2 2.8
SMT long and short terminals
140 mW
Unom. nominal coil voltage
1
2.6 For latching relays U resp. U
Weight set min. reset min.max. 2.8 g
Umax. at 0 A
0.8
2.4
Umax. at 2 x 1 A Resistance to soldering heat THT
Uop. min.
0.6
U = Lower limit of the operative range of
Umax. at 2 x 2 A rel. min.
2.2 IEC 60068-2-20 265C/10s
0.4
2 Moisturthe coil voltage (reliable release voltage)e sensitive level, JEDEC J-Std-020D MSL3
0.2
0 1.8 related only to SMT relays
-40-30 -20-10 0102030405060708090 100 110 120 130 140
1.6 packed in orginal dry-packs
Ambient Temperature [C]
Ultrasonic cleaning not recommended
1.4
Coil versions, high dielectric version, monostable, overmolded Packaging/unit
1.2
Unom. nominal coil voltage
Coil Rated1 Operate Limiting Release Coil Rated coil THT box/2000 pcs.
2.8
code voltage0.8 voltage Voltage Voltage resistance140 mW power SMT reel/2000 pcs. or 2500 pcs.
2.6
VDC0.6 VDC VDC VDC 10% mW
Umax. at 0 A
Uop. min.
2.4
008 3.000.4 2.25 6.1 0.30 Umax. at 2 x 1 45 A200
Urel. min.
Umax. at 2 x 2 A
2.2
001 5.00 3.75 10.1 0.50 125 200
0.2
2
002 6.00 4.50 12.1 0.60 180 200
0
-40-30 -20-10 0102030405060708090 100 110 120 130 140
006 9.001.8 6.75 18.2 0.90 405 200
Ambient Temperature [C]
003 12.001.6 9.00 24.2 1.20 720 200
All figures are given for coil without pre-energization, at ambient temperature +23C.
1.4
Other coil voltages on request.
1.2
Unom. nominal coil voltage
1
200 mW
2.8
0.8
2.6
Umax. at 0 A
0.6
Uop. min.
Umax. at 2 x 1 A
2.4
0.4
Urel. min.
Umax. at 2 x 2 A
2.2
0.2
2
0
-40-30 -20-10 0102030405060708090 100 110 120 130 140
1.8
Ambient Temperature [C]
1.6
1.4
1.2
Unom. nominal coil voltage
1
200 mW
2.8
0.8
2.6 Umax. at 0 A
0.6
Uop. min.
Umax. at 2 x 1 A
2.4
0.4
Urel. min.
Umax. at 2 x 2 A
2.2
0.2
2
0
-40-30 -20-10 0102030405060708090 100 110 120 130 140
1.8
Ambient Temperature [C]
1.6
1.4
2
10-2014, Rev. 10141.2 Datasheets and product specification Datasheets and product data is subject to the Datasheets, product data, Definitions sec-
Unom. nominal coil voltage
www.te.com according to IEC 61810-1 and to be used terms of the disclaimer and all chapters of tion, application notes and all specifications
1
2014 Tyco Electronics Corporation, only together with the Definitions section. the Definitions section, available at are subject to change.
0.8
All specications subject to change. Consult Tyco Electronics for latest specications. 5 of 15
a TE Connectivity Ltd. company