420 W 200 W 100 W 30 W Automotive Relays PCB Double Relays Double Micro Relay K (THT THR) Small power relay Limiting continuous current 20A at 85C Minimal weight Low noise operation Wave (THT) and reflow (THR/pin-in-paste) solderable versions For single version refer to Single Micro Relay K Typical applications 086C/R2 fcw1b Door lock, heated front/rear screen, lamps front/rear/fog light, interior lights, seat control, sun roof, window lifter, wiper control. Contact Data Contact Data (continued) 6 Contact arrangement 2 form C, 2 CO Mechanical endurance > 5x10 ops. 2 Rated voltage 10/12VDC 1) Measured on 70x70x1.5mm epoxy PCB FR4 with 25cm (double layer 105m) 2 1) copper area. Connecting cable cross section 6 mm .Boundary conditions: 180C coil Rated current NO/NC temperature 130C solder joint. Only one relay energized. 30A/25A 2) The values apply to a resistive or inductive load with suitable spark suppression and at 1) Limiting continuous current maximum 13.5VDC for 12VDC load voltages. For a load current duration of maximum 23C 30/25A 3s for a make/break ratio of 1:10. 85C 20/15A 3) See chapter Diagnostics of Relays in our Application Notes or consult the internet at Automotive Relays PCB Double Relays Double Micro Relay K (THT THR) (Continued) Terminal Assignment Insulation Data Bottom view on solder pins Initial dielectric strength between open contacts 500VAC 2 form C, 2 CO rms between contact and coil 500VAC rms 13 14 22 15 11 Other Data EU RoHS/ELV compliance compliant 21 25 Ambient temperature -40 to +105C 12 Cold storage, IEC 60068-2-1 1000h -40C 24 23 Dry heat, IEC 60068-2-2 1000h +125C Climatic cycling with condensation, 86dtw ab EN ISO 6988 20 cycles, storage 8/16 h Temperature cycling (shock), IEC 60068-2-14, Na 100 cycles -40/+125C Temperature cycling, Dimensions IEC 60068-2-14, Nb 35 cycles -40/+125C Double Micro Relay THT Damp heat cyclic, IEC 60068-2-30, Db, Variant 1 6 cycles 25C/55C/93%RH 0,2 23,6 Damp heat constant, 0,1 IEC 60068-2-3 method Ca 56 days 40C/95%RH 6,2 Degree of protection 0,2 2,5 THT: RT III (61810) 0,2 0,6 THR: RT II (61810) Corrosive gas, IEC 60068-2-17: THT Qc, method 2, 1min, 70C IEC 60068-2-42 10 days IEC 60068-2-43 10 days Vibration resistance (functional) 5) IEC 60068-2-6 (sine sweep) 10 to 500Hz 6g Shock resistance (functional) 5) IEC 60068-2-27 (half sine) 6ms, up to 30g Terminal type PCB:THT, THR Weight approx. 8g (0.28oz) A Solderability (aging 3: 4h/155C) THT, IEC 60068-2-20 Ta, method 1, hot dip 5s, 215C 0,3 12,9 Resistance to soldering heat THT, 0,2 0,95 IEC 60068-2-20 Tb, method 1A, hot dip 10s, 260C, with thermal screen Resistance to soldering heat THR, IEC 60068-2-58 260C preheating min 130C 6) Storage conditions according IEC 60068-1 Packaging unit 990 pcs. 5) Depending on mounting position: no change in the switching state >10s. 6) For general storage and processing recommendations please refer to our Application *) Additional tin tops Notes and especially to Storage in the Definitions or at