V23132E2001A200 TE Connectivity

Automotive Relays High Current Devices High Current Relay 150 n Limiting continuous current 130A at 85C n Current switching ability up to 300A n Suitable for voltage levels up to 24VDC n Heat, moisture and vibration resistant n Minimal contact resistance n Dustproof and sealed versions Typical applications Engine control, glow plug, heated front screen, preheating systems (e.g. for diesel engines, catalytic converters), switches for loading ramps, start/stop. F132 fcw2b Contact Data Coil Data Contact arrangement 1 form A, 1 NO Rated coil voltage 12/24VDC 1) 1 form B, 1 NC Rated coil power 3.3W 1 form C, 1 CO Max. coil temperature 155C 1 form X, 1 NO DM 1) Rated voltage 12VDC/24VDC Coil versions, DC coil A) Max. switching voltage depends on load parameters Coil Rated Operate Release Coil Rated coil 2 Rated current, cable 25mm 130A at 85C code voltage voltage voltage resistance power Limiting continuous current VDC VDC VDC 10% W 2 23C, load cable 16mm 130A 001 12 7.2 1.2 37 3.9 2 85C, load cable 16mm 120A 002 24 14.4 2.4 141 4.1 2 1) With resistor. 125C, load cable 16mm 60A 2 All figures are given for coil without preenergization, at ambient temperature +23C. 23C, load cable 25mm 180A 2 85C, load cable 25mm 130A 2 125C, load cable 25mm 70A Coil operating range ECR1449-V Limiting making current, load current max. 3s on, 300 make/break ratio 1:10 300A Limiting breaking current 300A Contact material AgSnO 2 4) Min. recommended contact load 1A at 5VDC Initial voltage drop, typ. at 100A 70mV Frequency of operation, with/without load 6 ops./min Operate/release time typ. at nominal voltage 25/8ms Electrical endurance Does not take into account form A contact (NO), resistive load, the temperature rise due to 4 cyclic temperature:+23C >5x10 cycles at 300A, 13.5VDC the contact current 7 E = pre-energization Mechanical endurance >10 ops. A) Please contact TE relay application engineer. Does not take into account the temperature rise due to the contact current E = pre-energization Insulation Data Initial dielectric strength between contact and coil 1000VAC rms Load dump test ISO 7637-1 (12VDC), test pulse 5 Vs=+86.5VDC ISO 7637-2 (24VDC), test pulse 5 Vs=+200VDC 1 03-2014, Rev. 0314 Datasheets and product specification ac- Datasheets and product data is subject to the Datasheets, product data, Definitions sec- www.te.com cording to IEC 61810-1 and to be used only terms of the disclaimer and all chapters of tion, application notes and all specifications 2014 Tyco Electronics Corporation, together with the Definitions section. the Definitions section, available at are subject to change. a TE Connectivity Ltd. company. Automotive Relays High Current Devices High Current Relay 150 (Continued) Other Data Other Data (continued) EU RoHS/ELV compliance compliant Terminal type screw Ambient temperature -40C to +125C Cover retention Dry heat, IEC 60068-2-2 500h at 100C pull force 500N Damp heat constant, push force 500N IEC 60068-2-3 (78), Ca 500h, 40C, 93% RH Terminal retention Degree of protection pull force 150N dustproof: IP54 (IEC 60529), RT I (IEC 61810) push force 150N sealed: sealing in accordance with IEC 68 resistance to bending 20N immersion cleanable: IP67 (IEC 60529), RT III (IEC 61810) force applied to side 20N Corrosive gas torque 5Nm IEC 60068-2-42 10 days Weight approx. 220g (7.8oz) IEC 60068-2-43 10 days Packaging unit 50 pcs. 2) No change in the switching state >10s. Vibration resistance (functional) 2) IEC 60068-2-6 (sine sweep) 10 to 200Hz >5g Shock resistance (functional) 2) IEC 60068-2-27 (half sine) 6ms >20g Drop test, free fall IEC 60068-2-32 1m onto concrete Terminal Assignment NOR COR NOBRR 1 form A, 1 NO with resistor 1 form C, 1 CO with resistor 1 form X, 1 NO DM with resistor 2 5 2 54 2 55b 1 3 1 3 1 Dimensions View of the terminals NO and NO DM version Bottom view 84 84 40 40 63 63 15.5 7.5 x 6.5 7.5 x 6.5 45 45 *) 65.2 65.2 13.5 13.5 71 71 6.5 6.5 TE1667-61 TE1666-X1 TE1666-X1 Connector Connector 17 17 *) Alternatively 5b for form X, 1 NO DM with resistor. Screw terminals M6Screw terminals M6 2-pole 2-pole Connector Information AMP SUPERSEAL 1.5 SERIES Coil side - Receptacle connector 282080-1 - Single wire seal 281934-2 - Contact 282110-1 Load side Cable lug M6, maximum cable section 25 mm 2 03-2014, Rev. 0314 Datasheets and product specification ac- Datasheets and product data is subject to the Datasheets, product data, Definitions sec- www.te.com cording to IEC 61810-1 and to be used only terms of the disclaimer and all chapters of tion, application notes and all specifications 2014 Tyco Electronics Corporation, together with the Definitions section. the Definitions section, available at are subject to change. a TE Connectivity Ltd. company.