V23234-A0001-X032 TE Connectivity

Automotive Relays Plug-in Mini ISO Relays Power Relay B n Pin assignment similar to ISO 7588 part 1 n Plug-in terminals n Customized versions on request 24VDC versions with contact gap >0.8mm Integrated components (e.g. resistor, diode) Customized marking/color Special covers (e.g. notches, release features, brackets) Various contact arrangements and materials Typical applications Cross carline up to 35A for example: rear window defogger, battery disconnection, power distribution (clamp 15) F234 fcw1 bw Contact Data 1 A 1 A 1 C 1 C Contact arrangement 1 form A, 1 form A, 1 form C, 1 form C, 1 NO 1 NO 1 CO 1 CO Rated voltage 12VDC 24VDC 12VDC 24VDC Coil Data Limiting continuous current Rated coil voltage 12/24VDC form A/form B (NO/NC) 23C 50A 50A 50/35A 50/35A Coil versions, DC coil 85C 35A 35A 35/25A 35/25A Coil Rated Operate Release Coil Rated coil 5) 5) 125C 15A 15A 15/10A 15/10A code voltage voltage voltage resistance power 1) Limiting making current VDC VDC VDC 10% W A/B (NO/NC) 120A 120A 120/45A 120/45A 001 12 8 1.5 85 1.7 Limiting breaking current, 002 12 6.5 1 75 1.9 A/B (NO/NC) 30A 20A 30/20A 20/10A 004 24 16 3 255 2.3 5) Without components in parallel. Limiting short-time current 2) All figures are given for coil without pre-energization, at ambient temperature +23C. overload current, ISO 8820-3 1.35 x 35A, 1800s 2.00 x 35A, 5s 3.50 x 35A, 0.5s Insulation Data 6.00 x 35A, 0.1s Initial dielectric strength Jump start test, ISO 16750-1 24VDC for 5min, between open contacts 500V rms conducting nominal current at 23C between contact and coil 500V rms Contact material Silver based between adjacent contacts 500V rms 3) Min. recommended contact load 1A at 5VDC Load dump test Initial voltage drop, at 10A, typ./max. ISO 7637-1 (12VDC), test pulse 5 V =+86.5VDC s form A (NO) 15/300mV 15/300mV 15/300mV 15/300mV ISO 7637-2 (24VDC), test pulse 5 V =+200VDC s form B (NC) - - 20/300mV 20/300mV Frequency of operation, at nominal load 6 ops./min (0.1Hz) 4) Operate/release time typ. 10/10ms Other Data Electrical endurance, ops. EU RoHS/ELV compliance compliant 5 5 5 5 6) resistive load, A (NO) >2.5x10 >2.5x10 >2.5x10 >2.5x10 Protection to heat and fire according UL94 HB or better 30A, 20A, 30A, 20A, Ambient temperature -40 to 125C 14VDC 28VDC 14VDC 28VDC Climatic cycling with condensation, 5 5 resistive load, B (NC) - - >1x10 >2.5x10 EN ISO 6988 6 cycles, storage 8/16h 20A, 10A, Temperature cycling, 14VDC 28VDC IEC 60068-2-14, Nb 10 cycles, -40/+85C (5C/min) 6 Mechanical endurance typ. 1x10 ops. Damp heat cyclic, 1) The values apply to a resistive or inductive load with suitable spark suppression and IEC 60068-2-30, Db, Variant 1 6 cycles, upper air temp. 55C at maximum 14VDC for 12VDC or 28VDC for 24VDC load voltages. For a load current Damp heat constant, IEC 60068-2-3, Ca 56 days duration of maximum 3s for a make/break ratio of 1:10. Category of environmental protection, 2) Current and time are compatible with circuit protection by a typical automotive fuse. IEC 61810 RT I dustproof Relay will make, carry and break the specified current. Degree of protection, IEC 60529 IP54 3) See chapter Diagnostics of Relays in our Application Notes or consult the internet at Corrosive gas Automotive Relays Plug-in Mini ISO Relays Power Relay B (Continued) Other Data (continued) Accessories Terminal type plug-in, QC For details see datasheet Connectors for Mini ISO Relays Cover retention axial force 150N pull force 200N push force 200N 8) Terminal retention pull force 100N push force 100N resistance to bending 10N force applied to side 10N torque 0.3Nm Weight approx. 35g (1.2oz) Packaging unit 200 pcs. 6) Refers to used mateials. 7) No change in the switching state >10s. Valid for NC contacts, NO contact values significantly higher. 8) Values apply 2mm from the end of the terminal. When the force is removed, the terminal must not have moved by more than 0.3mm. Terminal Assignment NO NOR NO 2x87 NOR 2x87 1 form A, NO 1 form A, NO with resistor 1 form A, 1 NO (2x87) 1 form A, 1 NO (2x87) with resistor 85 87 87 85 87 87 85 87 85 87 86 30 86 30 86 30 86 30 NOD 2x87 CO COR COD 1 form A, 1 NO (2x87) with diode 1 form C, CO 1 form C, CO with resistor 1 form C, CO with diode 85 87 87a 85 87 87a 85 87 87a 85 87 87 86 30 86 30 86 30 86 30 2 06-2011, Rev. 0611 Datasheets and product specification ac - Datasheets and product data is subject to the Datasheets, product data, Definitions sec - www.te.com cording to IEC 61810-1 and to be used only terms of the disclaimer and all chapters of tion, application notes and all specifications 2011 Tyco Electronics Corporation, together with the Definitions section. the Definitions section, available at are subject to change. a TE Connectivity Ltd. company.