YD369-R33-BP000000 TE Connectivity

D369-R33-NS1 K1316 H++++D 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 A NOTES: 3 WAY CONNECTOR 1 MARKED WITH TE PART NUMBER, CAGE CODE AND DATE CODE. PART NUMBER EXAMPLE: D369 - H R 3 3 - N S 1 10.70 MAX. BASIC PART NUMBER CONTACT CONFIGURATION 4 HARSH ENVIRONMENT CONTACT TYPE (P=PIN, S=SKT) 21.46 MAX. D1 B B 2 (OMIT FOR CABIN VARIANT ) SHELL KEYING SHELL STYLE (R=RECEPTACLE) SHELL SIZE (3, 6 OR 9) B CONTACT QUANTITY (3=3 x 22, 6=6 x 22, 9=9 x 22) +Y -Y C BOEING PART NUMBER EXAMPLE: BACC65CR 1 S N C MARKED ON BASIC PART NUMBER SHELL KEY BAG ONLY D2 SHELL SIZE CONTACT TYPE (1=SIZE 3, 2=SIZE 6, 3=SIZE 9) (PIN=PIN, S=SKT) -X +X BOEING PART STANDARD BACC65CR REVISION B REFERS. N.B. BACC65CR*** PART NUMBERS ARE SUPPLIED WITHOUT CONTACTS. A D D 2 PERFORMANCE: CABIN CONNECTOR HARSH ENVIRONMENT CONNECTOR D369-R**-*** D369-HR**-*** OR BACC65CR*** 9 COORDINATE POSITIONS OF CONTACTS (3 WAY ONLY) TEMPERATURE RANGE -55 C TO +175 C DIELECTRIC WITHSTAND 1500VRMS <2mA LEAKAGE CONTACT LOCATION CONTACT VOLTAGE (AT SEA LEVEL) POSITION (ID) X AXIS (mm) Y AXIS (mm) DURABILITY 500 MATING CYCLES MIN. E E 1 -2.54 0 INSULATION RESISTANCE 5000 M INITIAL 2 0 0 IP RATING IP65 IP67 3 2.54 0 SEALING RTCA DO160 - CATEGORY A4 (15,000ft) EN2591-314: 12.1kPa (1.75psi) 15km (50,000ft) HUMIDITY RTCA DO160 - CATEGORY A EN2591-321 / EIA-364-31 METHOD IV 1 PART MARKING 3. INSERTION / EXTRACTION TOOL (M81969/14-01 OR EQUIVALENT) SUPPLIED SEPARATELY. F F 4 CONTACT CONFIGURATION: CONTACT P/N (OR EQUIVALENT) CRIMP POSITIONER CONTACT CRIMP WIRE CURRENT CONFIG. DESCRIPTION TOOL ACCOMODATION RATING PIN SOCKET PIN SOCKET 5.91 0 NO CONTACTS SUPPLIED 5.31 CRIMP, COPPER (PIN INSERT) 1 38941-22L 38946-22L M22520/2-09 M22520/2-06 M22520/2-01 22-28 AWG 5A (22 AWG) WIRE CRIMP, ALUMINIUM G G 2 200-1042-22 200-1142-22 KAL2 ALNP 22-A 22 AWG 5A WIRE CRIMP, ENLARGED 3 182-0860-22 182-0862-22 M22520/2-09 M22520/2-06 M22520/2-01 20-24 AWG 5A (20 AWG) COPPER WIRE 5. MATERIALS: MATERIAL COMPONENT PIN / MALE (FINISH: CLEAN IN ALL CASES) H H CONTACT CAVITY SEALS SILICONE / FLUOROSILICONE BLEND RUBBER IDENTIFICATION ON REAR BODY / INSERT THERMOPLASTIC COMPONENTS 0.71 0.11 (SOCKET INSERT) 6. IF FILLER PLUGS ARE REQUIRED, USE THE FOLLOWING: TE PART NUMBER - 600300-22. MIL-SPEC PART NUMBER - MS27488-22-2. J J SHELL COLOUR IS KEYING 7. MAXIMUM WEIGHTS (WITHOUT CONTACTS): DEPENDANT (SEE TABLE) 3 WAY - 1.0g (PIN INSERT), 1.0g (SOCKET INSERT). 6 WAY - 1.4g (PIN INSERT), 1.5g (SOCKET INSERT). 9 WAY - 2.0g (PIN INSERT), 1.9g (SOCKET INSERT). 8 FOR ALL HARSH ENVIRONMENT VARIANTS, THE REAR BODY IS TO BE COLOURED DARK BLUE. ACCESSORY OR BOOT MOUNTING 9 DIMENSIONS ARE TRUE POSITIONS OF CAVITIES AT FRONT OF PIN INSERT (SOCKET OPPOSITE). SOCKET / FEMALE FEATURE K K CONTACT CAVITY CENTRE OF EACH CAVITY 0.20 A B . IDENTIFICATION ON REAR SHELL KEYING (ALL SIZES) POSITIONS (0.03) ORIENTATION COLOUR D1 D2 N BLACK -2.35 2.90 L A DARK RED -2.35 -2.90 L MATERIAL: FINISH: B DARK BLUE -1.175 -2.90 BS8888 SEE NOTES REAR WIRE SEAL C DARK GREEN 0 -2.90 THIRD ANGLE PROJECTION D YELLOW 1.175 -2.90 8 REAR BODY TYPE: CUSTOMER DRAWING TITLE: UNLESS OTHERWISE STATED: TE CONNECTIVITY UK LTD., 369 RECEPTACLE CONNECTOR, DIMENSIONS: mm INCHES ST. LEONARDS-ON-SEA, TN38 9RF, UK. ENVELOPE DRAWING SIZE: SCALE: DRAWING NUMBER: SHEET: ISSUE: AB DUK-70190 JCB RJM NDL CEO 04/02/2019 M M IF IN DOUBT, ASK IF IN DOUBT, ASK A1 5:1 1 OF 2 AB APP. ISSUE CHANGE NOTE DRAWN CHECKED APP. ENG. DATE 611253-ENV MARKETING 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 THIS INFORMATION IS CONFIDENTIAL AND PROPRIETARY TO TYCO ELECTRONICS CORPORATION AND ITS WORLDWIDE SUBSIDIARIES AND AFFILIATES (TE). IT MAY NOT BE DISCLOSED TO ANYONE, OTHER THAN TE PERSONNEL, WITHOUT AUTHORIZATION FROM TE (www.TE.com). DRAWING NUMBER: 611253-ENV 9.89 MAX. 4.75 MAX. 6.80 MAX. D369-P66-NP1 K1316 H++++D D369-P99-NP1 K1316 H++++D 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 A 9 WAY CONNECTOR 6 WAY CONNECTOR 10.70 MAX. B B 21.46 MAX. 10.70 MAX. D1 21.46 MAX. D1 B B +Y +Y C C -Y -Y D2 D2 -X +X D D A -X +X A 9 COORDINATE POSITIONS OF CONTACTS COORDINATE POSITIONS OF CONTACTS 9 (6 WAY ONLY) (9 WAY ONLY) E E CONTACT LOCATION CONTACT CONTACT LOCATION CONTACT POSITION (ID) X AXIS (mm) Y AXIS (mm) POSITION (ID) X AXIS (mm) Y AXIS (mm) 1 -2.54 1.27 1 -2.54 2.54 2 0 1.27 2 0 2.54 3 2.54 1.27 3 2.54 2.54 4 2.54 -1.27 4 2.54 0 5 0 -1.27 F F 1 PART MARKING 5 0 0 6 -2.54 -1.27 1 PART MARKING 6 -2.54 0 7 -2.54 -2.54 0.71 8 0 -2.54 0.11 9 2.54 -2.54 (SOCKET INSERT) 0.71 0.11 G G (SOCKET INSERT) H H SOCKET / FEMALE CONTACT CAVITY IDENTIFICATION ON REAR 5.91 5.31 5.91 (PIN INSERT) 5.31 J J (PIN INSERT) SOCKET / FEMALE CONTACT CAVITY IDENTIFICATION ON REAR K K PIN / MALE CONTACT CAVITY IDENTIFICATION ON REAR L L MATERIAL: FINISH: BS8888 SEE NOTES THIRD ANGLE PROJECTION PIN / MALE TYPE: CUSTOMER DRAWING TITLE: CONTACT CAVITY UNLESS OTHERWISE STATED: IDENTIFICATION ON REAR TE CONNECTIVITY UK LTD., 369 RECEPTACLE CONNECTOR, DIMENSIONS: mm INCHES ST. LEONARDS-ON-SEA, TN38 9RF, UK. ENVELOPE DRAWING SIZE: SCALE: DRAWING NUMBER: SHEET: ISSUE: M M IF IN DOUBT, ASK A1 5:1 2 OF 2 AB 611253-ENV 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 THIS INFORMATION IS CONFIDENTIAL AND PROPRIETARY TO TYCO ELECTRONICS CORPORATION AND ITS WORLDWIDE SUBSIDIARIES AND AFFILIATES (TE). IT MAY NOT BE DISCLOSED TO ANYONE, OTHER THAN TE PERSONNEL, WITHOUT AUTHORIZATION FROM TE (www.TE.com). DRAWING NUMBER: 611253-ENV 9.89 MAX. 9.83 MAX. 11.90 MAX. 9.89 MAX. 7.29 MAX. 9.40 MAX.