FR75-1 Teledyne

Series FR75-1 1.0A, 60 Vdc Optically Isolated Short-Circuit Protected Part Number Description FR75-1 1A, 60 Vdc short-circuit protected solid-state relay for through-hole mount ELECTRICAL SPECIFICATIONS (40C to +85C ambient temperature unless otherwise specified) INPUT (CONTROL) SPECIFICATIONS Min Max Units Input Voltage Range 4.5 5.5 Vdc (See Note 1) FEATURES/BENEFITS Input Current 5 Vdc (See Figure 2) 15 mA Short-circuit protected: Prevents damage to system components, assemblies and system Must Turn-On Voltage 3.8 Vdc wiring Must Turn-Off Voltage 1.5 Vdc Optical isolation: Isolates control circuits from Must Turn-Off Current 50 Adc load transients and eliminates ground loops and Reserve Polarity 10 Vdc signal ground noise Low off-state leakage: For high off-state OUTPUT (LOAD) SPECIFICATIONS impedance Switches high currents: To 1.0 Adc Min Max Units High noise immunity: Control signals isolated Load Voltage Range 60 Vdc from switching noise Output Current Rating (See Figure 4) 1.0 Adc High dielectric strength: For safety and for Leakage Current at Rated Voltage 100 Adc protection of control and signal level circuits Transient Blocking Voltage 80 Vdc Output Capacitance 25Vdc (25C) 600 pF DESCRIPTION Output Voltage Drop 0.32 Vdc The FR75-1 solid-state relay utilizes a power FET switch that is protected against short circuits and On Resistance 0.32 Ohm overload currents. The short-circuit protection feature Turn-On Time 3.0 ms provides protection when a short or overload occurs Turn-Off Time 0.3 ms while the relay is on as well as when the relay is Trip Overload (See Figure 6) 6 Adc switched into a short. In either case, the relay will sense the short-circuit condition and then block it indefinitely until the short is removed and the unit is reset by cycling the input control. Using the FR75-1 MECHANICAL SPECIFICATION to switch power sources and loads prevents damage TOP VIEW BOTTOM VIEW 0.109 REF (2.769) to system assemblies and system wiring. The power WEIGHT: .07 OZ. (2g) 0.079 REF FET output offers low ON resistance and can switch (2.007) 3 1 0.017 1 3 loads in either the high or the low side of the power (0.432) FR75-1 +0.002 TELEDYNE 0.001 line. The FR75-1 is packaged in a low-profile mini- 6 4 46 DIP package. 0.010 (0.254) 0.70 MIN 0.003 0.190 (17.78) 0.200 (5.08) 0.423 MAX (10.74) MAX (4.83) Material and Plating: Pins and Header Kovar gold plated Cover Nickel Tolerance: 0.005 inch unless otherwise specified Figure 1 FR75-1 mechanical specification dimensions in inches (mm) FR75-1 38 SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE 2002 TELEDYNE RELAYS FR75-1 072002 Q1 0.463 MAX (11.76) 0.300 (7.62)FR75-1 GENERAL SPECIFICATIONS INPUT CURRENT VS. INPUT VOLTAGE (+25C ambient temperature unless otherwise specified) 18 16 ENVIRONMENTAL SPECIFICATION 14 Min Max Units 12 Operating Temperature 40 +85 C Storage Temperature 55 +125 C 10 Junction Temperature 1A +125 C 8 Thermal Resistance 125 C/W JA 6 Shock 1500 g 4 Vibration 100 g Dielectric Strength 500 Vac 2 Insulation Resistance 0 0 1 2 3 4 5 6 7 8 9 10 9 ( 500 Vdc) 10 Ohm Input Voltage (V) Input to Output Capacitance 5 pF Altitude 55,000 ft. Figure 2 FR75-1 input current vs. input voltage Resistance to Soldering Heat MIL STD 202, method 210 Solderability MIL STD 202, method 208 Thermal Shock MIL STD 202, method 107 FUNCTIONAL BLOCK DIAGRAM +IN (1) +OUT (4) Output Switch INPUT Optical Detection Switching (MOSFET) with Isolation Circuit Circuit with Current LEDs Sense OUT (6) -IN (3) Figure 3 FR75-1 functional block diagram LOAD CURRENT VS. AMBIENT TEMPERATURE TYPICAL WIRING DIAGRAM 1.2 +5 Vdc Bias 1.0 4 1 + +out +in DC 0.8 Power FR75-1 24-48 Vdc Typical 0.6 3 6 LOAD in out 0.4 Control 0.2 0 -55 -35 -15 5 25 45 65 85 105 125 Figure 5 FR75-1 typical wiring diagram Ambient Temperature (C) Figure 4 FR75-1 load current vs. ambient temperature 2002 TELEDYNE RELAYS (800) 284-7007 www.teledynerelays.com FR75-1 39 FR75-1 072002 Q1 Load Current (A) Input Current (mA)