Series 114
DPDT Non-Latching
Established Reliability / Military Relay
CENTIGRID
ESTABLISHED RELIABILITY
MILITARY
DPDT
SERIES RELAY TYPE
114 DPDT basic relay
114D DPDT relay with internal diode for coil transient suppression
114DD DPDT relay with internal diodes for coil transient suppression and polarity reversal protection
DESCRIPTION
The 114 sensitive Centigrid relay retains the same features as the 114
High force/mass ratios for resistance to shock and vibration.
standard Centigrid relay with only a minimal increase in profile height
Precious metal alloy contact material with gold plating assures excellent
(.275 in.). Its .100-inch grid spaced terminals, which preclude the need for
high current and dry circuit switching capabilities.
spreader pads, and its low profile make the 134 relay ideal for applications
where high packaging density is important.
The Series 114D and 114DD have internal discrete silicon diodes for coil
suppression and polarity reversal protection.
The following unique construction features and manufacturing techniques
provide excellent resistance to environmental extremes and overall high
reliability:
By virtue of its inherently low intercontact capacitance and contact circuit
losses, the 114 relay has proven to be an excellent ultraminiature RF
The 114 feature:
switch for frequency ranges well into the UHF spectrum. A typical RF
application for the Centigrid relay is in handheld radio transceivers,
All welded construction.
wherein the combined features of good RF performance, small size, low
Advanced cleaning techniques provide maximum assurance of internal
coil power dissipation and high reliability make it a preferred method of
cleanliness.
Transmit-Receive switching
Unique uni-frame design providing high magnetic efficiency and
mechanical rigidity.
ENVIRONMENTAL AND
INTERNAL CONSTRUCTION
PHYSICAL SPECIFICATIONS
Temperature
UPPER
65C to +125C
UNI-FRAME
(Ambient) STATIONARY
CONTACT
Vibration
ARMATURE
30 gs to 3000 Hz
(General Note I)
LOWER
Shock 75 gs,
STATIONARY
CONTACT
(General Note I) 6ms half sine
MOVING
CONTACT
Acceleration 50 gs
Enclosure Hermetically sealed
Weight 0.09 oz. (2.55g) max.
2016 TELEDYNE RELAYS (800) 284-7007 www.teledynerelays.com 114 Page 1
114\032016\Q1INSERTION LOSS
Series 114
DPDT Non-Latching
Established Reliability / Military Relay
SERIES 114
GENERAL ELECTRICAL SPECIFICATIONS (@25C)
Contact Arrangement 2 Form C (DPDT)
Rated Duty Continuous
Contact Resistance 0.1 ohm max. before life; 0.2 ohm max. after life at 1A/28Vdc
Resistive: 1 A/ 28 Vdc
Inductive: 200 mA/ 28 Vdc (320mH)
Contact Load Rating (DC)
Lamp: 100 mA / 28 Vdc (320mH)
Low level: 10 to 50 A @ 10 to 50 mV
Resistive: 250 mA / 115Vac, 60 and 400 Hz (Case not grounded)
Contact Load Rating (AC)
100 mA / 115 Vac, 60 and 400 Hz (Case grounded)
10,000,000 cycles (typical) at low level
Contact Life Ratings 1,000,000 cycles (typical) at 0.5 A / 28 Vdc resistive
100,000 cycles min. at all other loads speci ed above
Contact Overload Rating 2 A / 28 Vdc Resistive (100 cycles min.)
Contact Carry Rating Contact Factory
Operate Time 2.0 msec max. at nominal rated coil voltage
114 1.5 ms max.
Release Time
114D
4.0 ms max
114DD
Contact Bounce 1.5 msec max.
Intercontact Capacitance 0.4 pf typical
Insulation Resistance 10,000 M min. between mutually isolated terminals
Dielectric Strength
Atmospheric pressure: 500 Vrms 70,000 ft: 125
(Vrms/60)
Negative Coil 114D
1.0 Vdc Max.
Transient (Vdc) 114DD
114D
Diode P.I.V. (Vdc) 100 Vdc Min.
114DD
GENERAL NOTES
PERFORMANCE CURVES (Note 2)
1. Relay contacts will exhibit no chatter in
TYPICAL RF PERFORMANCE TYPICAL DC CONTACT RATING (RESISTIVE)
excess of 10 sec or transfer in excess
0
of 1 sec.
.1
2. Typical characteristics are based on
.2 300
available data and are best estimates.
.3
250
No on-going verification tests are
.4
performed.
200
10 1.92
3. Unless otherwise specified, parameters
20 1.22
150 are initial values.
30 1.07
4. Relays can be supplied with a spacer
100
40 1.02
pad. See appendix.
50
1.01
50
60 1.00
70 1.00
0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0
.01 0.5 .1 .5 1.0
LOAD CURRENT (AMPS DC)
FREQUENCY (GHz)
FIGURE 2
FIGURE 1
114 Page 2 SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE 2016 TELEDYNE RELAYS
114\032016\Q1
RETURN LOSS (VSWR)
ISOLATION ACROSS POLES
ISOLATION ACROSS CONTACTS
dB
VSWR
LOAD VOLTAGE (VDC)
