S172-5 Teledyne

SERIES CENTIGRID S172 SURFACE MOUNT COMMERCIAL RELAYS DPDT SERIES RELAY TYPE DESIGNATION S172 DPDT basic relay S172D DPDT relay with internal diode for coil transient suppression INTERNAL CONSTRUCTION DESCRIPTION UNI-FRAME The S172 surface mount Centigrid relay is an ultraminiature, hermetically sealed, armature relay for commercial applications. Its low profile height (.470) ARMATURE and .100 grid spaced terminals make it an ideal choice where extreme UPPER STATIONARY CONTACT packaging density and/or close PC board spacing are required. The specially MOVING CONTACT formed leads are pre-tinned to make the relays ideal for all types of surface- LOWER STATIONARY CONTACT mount solder reflow processes. The basic design and internal structure are similar to Teledynes DPDT 114 Centigrid relay. Unique construction features and manufacturing techniques provide overall high reliability and excellent resistance to environmental extremes: All welded construction. Unique uni-frame design providing high magnetic efficiency and mechanical ENVIRONMENTAL AND rigidity. PHYSICAL SPECIFICATIONS High force/mass ratios for resistance to shock and vibration. Storage 65C to +125C Temperature (Ambient) Advanced cleaning techniques provide maximum assurance of internal 55C to +85C Operating cleanliness. Vibration 10 gs to 500 Hz (General Note 1) Precious metal alloy contact material with gold plating assures excellent Shock 30 gs, high current and dry circuit switching capabilities. (General Note 1) 6 msec, half-sine Enclosure Hermetically sealed Weight 0.15 oz. (4.3g) max. The S172D relay has an internal discrete silicon diode for coil transient 260C max. temp. suppression. Reflow Temperature 1 min. max. 2003 TELEDYNE RELAYS SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE S172 Page 1 www.teledynerelays.com S172/1203/Q1 CENTIGRID AND TO-5 CENTIGRID AND TO-5 SERIES S172 GENERAL ELECTRICAL SPECIFICATIONS ( 25C) (Notes 2 & 3) Contact Arrangement 2 Form C (DPDT) Rated Duty Continuous Contact Resistance 0.15 ohm max. before life 0.3 ohm max. after life at 1A/28Vdc (measured 1/8 from header) Resistive: 1 Amp/28Vdc Contact Load Ratings (DC) Inductive: 200 mA/28Vdc (320 mH) (See Fig. 1 for other DC Lamp: 100 mA/28Vdc resistive voltage/current ratings) Low Level: 10 to 50 A/10 to 50mV 5,000,000 cycles (typical) at low level Contact Life Ratings 500,000 cycles (typical) at 0.5A/28Vdc resistive 100,000 cycles min. at all other loads specified above Contact Overload Rating 2A/28Vdc Resistive (100 cycles min.) Contact Carry Rating Contact factory Operate Time 6.0 msec max. at nominal rated coil voltage Release Time S172: 3.0 msec max. S172D: 6.0 msec max. Contact Bounce 1.5 msec max. Intercontact Capacitance 0.4 pf typical Insulation Resistance 1,000 megohms min. between mutually isolated terminals Dielectric Strength Atmospheric pressure: 300 Vrms/60Hz Negative Coil Transient (Vdc) S172D 2.0 max Diode P.I.V. (Vdc) S172D 60 min. DETAILED ELECTRICAL SPECIFICATIONS ( 25C) (Note 3) BASE PART S172-5 S172-12 S172-26 NUMBERS S172D-5 S172D-12 S172D-26 Nom. 5.0 12.0 26.5 Coil Voltage (Vdc) Max. 5.8 16.0 32.0 Coil Resistance (Ohms 20%) 64 400 1600 Pick-up Voltage (Vdc, Max.) Pulse Operation 3.8 9.0 18.0 Coil Operating Power at Nominal Voltage (Milliwatts) 405 360 440 TYPICAL DC CONTACT RATINGS (RESISTIVE) GENERAL NOTES 1. Relay contacts will exhibit no chatter in excess of 10 sec 300 or transfer in excess of 1 sec. 250 2. Typical characteristics are based on available data and are best estimates. No on-going verification tests are 200 performed. 150 3. Unless otherwise specified, parameters are initial values. 4. Position of leads as they emerge from relay base. 100 5. Leads will fit noted pad layout with no overhang. 50 6. Lead ends are coplanar within .008 wide tolerance zone. 7. Terminals coated with SN60 or SN63 solder per QQ-S- 0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 571. Base material exposed at sheared end of leads. LOAD CURRENT (AMPS DC) 8. Add/ to end of part number for RoHS compliant solder FIGURE 1 coated pins (Sn99.3/Cu0.7). LOAD VOLTAGE (VDC)