23.0 mm (overall width). 91.0 mm (overall length). 91.0 mm (overall length). 22 mm maxi.. 15 mm maxi.. 6 mm (width of the end). The 4 mm banana female connection European Union marking. Current and voltage complies with the 4 mm banana plugs of the markings. worldwide most famous manufacturers. Fichier Datasheet TENMA 5004-LM-IEC. 28/11/2016. Indice A. Information in this publication supersedes all earlier versions. Specifications subject to change without notice. 2016. Dimensions in millimeters. 31.0 mm (overall height). 37.5 mm (overall height). ACCESSIBLE. Able to be touched with a standard test finger or test pin. BASIC INSULATION. Insulation of HAZARDOUS LIVE parts which provides basic protection. CAT II. Measurement or overvoltage category II. For measurement performed on / equipment connected to the building wiring. CAT III. Measurement or overvoltage category III. For measurement performed on / equipment connected to part of a building wiring installation. CAT IV. Measurement or overvoltage category IV. For measurement According to EN / IEC 61010-031:2008. 1000 V CAT II / 1000 V CAT III performed on / equipment connected to the origin of the electrical supply to a building. / 600 V CAT IV, reinforced insulation, 20 A (at +40 C). CLEARANCE. Shortest distance in air between two conductive parts. CREEPAGE DISTANCE. Shortest distance along the surface of a solid These specifications come from the creepage distances, clearances, accessible parts, and insulating material between two conductive parts. solid insulation of the clip. And the considered specifications of the environment are : CTI. Comparative Tracking Index of the insulating material in accordance pollution degree, 1 or 2 with IEC 60112. relative humidity, 80 % maximum for temperatures up to 31 C decreasing linearly to DOUBLE INSULATION. Insulation comprising both BASIC INSULATION and SUPPLEMENTARY INSULATION. 50 % relative humidity at +40 C EN / IEC 60529. European / international standard regarding the degrees of temperature range, +5 C to +40 C Barrier. Keep behind this protection provided by enclosures. indoor use and barrier to operate safely the EN / IEC 61010-1. European / international standard regarding the safety altitude, 2000 m maximum. requirements for electrical equipment for measurement, control, and clip while connecting to laboratory use Part 1: General requirements. hazardous live voltages (more EN / IEC 61010-031. European / international standard regarding the safety requirements for electrical equipment for measurement, control and than 33 V AC and 70 V DC). laboratory use Part 031: Safety requirements for hand-held probe assemblies for electrical measurement and test. According to EN / IEC 60529. IP2X (touchproof) when the jaws are closed. LV. European Directive 2014/35/EU on the harmonization of the laws of Member States relating to electrical equipment designed for use within certain voltage limits. (Usually called the Low Voltage Directive.) -20 C mini., +80 C maxi. (please see above too). MAINS. Low-voltage electricity supply system to which the equipment concerned is designed to be connected for the purpose of powering the equipment. European DirectiveLow Voltage Directiv 2006/95/EC. MAINS CIRCUIT. Circuit which is intended to be directly connected to the International / European standard EN / IEC 61010-031:2008. MAINS for the purpose of powering the equipment. European DirectiveRoH 2011/65/EU. OVERVOLTAGE CATEGORY. Numeral defining a TRANSIENT European REACH regulation n1907 / 2006. OVERVOLTAGE condition. International / European standard EN / IEC 60529. POLLUTION. Addition of foreign matter, solid, liquid or gaseous (ionized gases), that may produce a reduction of dielectric strength or surface Standard NF C 93-440:1986. resistivity. POLLUTION DEGREE. Numeral indicating the level of POLLUTION that RoH compliant, Pb 4 % in conductor, Pb 0.1 % in insulator, Hg 0.1 %, may be present in the environment. Cr VI 0.1 %, Cd 0.01 %, PBB 0.1 %, and PBDE 0.1 %. POLLUTION DEGREE 1. No POLLUTION or only dry, non-conductive REACH compliant, no substances from the candidate list of SVHC for authorisation at POLLUTION occurs, which has no influence. mass concentrations greater than 0.1 %. POLLUTION DEGREE 2. Only non-conductive POLLUTION occurs except that occasionally a temporary conductivity caused by condensation is expected. Conductors : nickel-coated steel, tinned steel, and brass. Insulators : please contact us. REINFORCED INSULATION. Insulation which provides protection against electric shock not less than that provided by DOUBLE INSULATION. Black Red Yellow Green Blue White RoH. European Directive 2011/65/EU on the restriction of the use of certain hazardous substances in electrical and electronic equipment. 0.023 kg. SOLID INSULATION. Insulating materials. Designed and manufactured in France. SUPPLEMENTARY INSULATION. Independent insulation applied in addition to BASIC INSULATION in order to provide protection against electric shock in the event of a failure of BASIC INSULATION. Year of 1st placing on the market 1995. TRANSIENT OVERVOLTAGE. Short duration overvoltage of a few milliseconds or less, oscillatory or non-oscillatory, usually highly damped. One piece per bag. WORKING VOLTAGE. Highest r.m.s. value of the a.c. or d.c. voltage across any particular insulation which can occur when the equipment is supplied at rated voltage. Fichier Datasheet TENMA 5004-LM-IEC. 28/11/2016. Indice A. Information in this publication supersedes all earlier versions. Specifications subject to change without notice. 2016. Dimensions in millimeters.