TLP2348 Photocouplers GaAAs Infrared LED & Photo IC TLP2348TLP2348TLP2348TLP2348 1. 1. 1. 1. ApplicationsApplicationsApplicationsApplications Intelligent Power Module Signal Isolation Programmable Logic Controllers (PLCs) High-Speed Digital Interfacing for Instrumentation and Control Devices 2. 2. GeneralGeneral 2. 2. GeneralGeneral The Toshiba TLP2348 consists of high-output GaAAs light-emitting diode coupled with a high-gain, high-speed photo detector. It is housed in the SO6 package. This product can operate in power supply voltage 4.5 V to 30 V with the maximum operative temperature of 110 . Since TLP2348 has guaranteed 3 mA low supply current (I /I ), and 1.6 mA low threshold input current CCL CCH (I ), it contributes to energy saving of devices. It can drive directly from a microcomputer for a low input current. FHL The detector has a totem-pole output stage with current sourcing and sinking capabilities. The TLP2348 has an internal Faraday shield that provides a guaranteed common-mode transient immunity of 30 kV/s. The TLP2348 has an inverter output. A buffer output version, the TLP2345, is also available. 3. 3. 3. 3. FeaturesFeaturesFeaturesFeatures (1) Inverter logic type (Totem pole output) (2) Package: SO6 (3) Operating temperature: -40 to 110 (4) Supply voltage: 4.5 to 30 V (5) Threshold input current: 1.6 mA (max) (6) Supply current: 3 mA (max) (7) Propagation delay time: t /t = 120 ns (max) pHL pLH (8) Pulse width distortion: t - t = 40 ns (max) pHL pLH (9) Common-mode transient immunity: 30 kV/s (min) (10) Isolation voltage: 3750 Vrms (min) (11) Safety standards UL-under application: UL1577 File No.E67349 cUL-under application: CSA Component Acceptance Service No.5A, File No.E67349 VDE-under application: Option (V4) EN60747-5-5 (Note)(Note)(Note)(Note) Note: When an EN60747-5-5 approved type is needed, please designate the Option (V4)Option (V4)Option (V4)Option (V4). 4. 4. Packaging and Pin ConfigurationPackaging and Pin Configuration 4. 4. Packaging and Pin ConfigurationPackaging and Pin Configuration 1: Anode 3: Cathode 4: GND 5: V (Output) O 6: V CC 11-4L1S 2013-12-04 1 Rev.1.0TLP2348 5. 5. 5. 5. Internal Circuit (Note)Internal Circuit (Note)Internal Circuit (Note)Internal Circuit (Note) Note: A 0.1-F bypass capacitor must be connected between pin 6 and pin 4. 6. 6. Principle of OperationPrinciple of Operation 6. 6. Principle of OperationPrinciple of Operation 6.1. 6.1. 6.1. 6.1. Truth TableTruth TableTruth TableTruth Table Input LED Output H ON L L OFF H 6.2. 6.2. Mechanical ParametersMechanical Parameters 6.2. 6.2. Mechanical ParametersMechanical Parameters Characteristics Min Unit Creepage distances 5.0 mm Clearance distances 5.0 Internal isolation thickness 0.4 7. 7. 7. 7. Absolute Maximum Ratings (Note)Absolute Maximum Ratings (Note)Absolute Maximum Ratings (Note)Absolute Maximum Ratings (Note) (Unless otherwise specified, T(Unless otherwise specified, T(Unless otherwise specified, T(Unless otherwise specified, T = 25 = 25 = 25 = 25 )))) aaaa Characteristics Symbol Note Rating Unit LED Input forward current I 15 mA F Peak transient input forward current I (Note 1) 1 A FPT Input power dissipation P 40 mW D Input reverse voltage V 5 V R Detector Output current I 50 / -50 mA O Output voltage V -0.5 to 30 V O Supply voltage V -0.5 to 30 V CC Output power dissipation P 100 mW O Output power dissipation derating (T 75 ) P /T -2 mW/ a O a Common Operating temperature T -40 to 110 opr Storage temperature T -55 to 125 stg Lead soldering temperature (10 s) T 260 sol Isolation voltage AC, 1 min., R.H. 60 % BV (Note 2) 3750 Vrms S Note: Using continuously under heavy loads (e.g. the application of high temperature/current/voltage and the significant change in temperature, etc.) may cause this product to decrease in the reliability significantly even if the operating conditions (i.e. operating temperature/current/voltage, etc.) are within the absolute maximum ratings. Please design the appropriate reliability upon reviewing the Toshiba Semiconductor Reliability Handbook Handling PrecautionDerating Concept and Method) and individual reliability data (i.e. reliability test report and estimated failure rate, etc). Note 1: Pulse width (PW) 1 s, 300 pps Note 2: This device is considered as a two-terminal device: Pins 1 and 3 are shorted together, and pins 4, 5 and 6 are shorted together. 2013-12-04 2 Rev.1.0