Non-contacting Position Sensor Magnepot 6150 7/8 Diameter Single Turn Non-contacting Position Sensor Model Styles Available 6153 1/8 Shaft, dual ball bearing 1/8 Shaft, 1/4 Bushing 615x-XXXX Custom models are available Contact Customer Service for special features Electrical Output Voltage 0.2 Vdc (4%) to 4.8 Vdc (96%) Typical (see Feature Codes table) Output Overvoltage Limits 10 Vdc to -0.3 Vdc output may be shorted to ground or supply without damage Output Current 8 mA maximum Output Load 1 k minimum, 10 k typical Input Voltage 4.5 to 5.5 Vdc Supply Voltage Absolute Limits 20 Vdc maximum, -10 Vdc minimum 2 Independent Linearity 0.5% (0.25% available) Hysteresis 0.2% maximum Resolution 0.088 for 360 travel, 0.011 for 45 travel Supply Current 8.5 mA typical, 12 mA maximum Dielectric Strength 750 V rms Insulation Resistance 1,000 Megohms minimum Electrostatic Discharge (ESD) Passes 2 kV human body model and 15 kV air discharge Bulk Current Injection (BCI) Passes 2-500 MHz at 200 mA Actual Electrical Travel 360 typical (see Ordering Information) 3 Temperature Coefficient of Output Voltage 20 ppm/C Mechanical Total Mechanical Travel 360 continuous Number of Gangs 1 maximum Weight 0.4 oz. nominal Shaft Runout maximum T.I.R. 0.003 Pilot Diameter Runout maximum T.I.R. 0.003 Lateral Runout maximum T.I.R. 0.003 Shaft Radial Play maximum 0.005 Start/Run Torque maximum 0.5 oz.-in. 1 Specifications subject to change without notice. 2 Linearity is measured between 1% and 99% of input voltage. 3 Measured with 5 VDC supply and 50% of electrical travel General Note TT electronics reserves the right to make changes in product specification without notice or liability. All information is subject to TT electronics own data and is considered accurate at time of going to print. www.bitechnologies.com TT electronics plc 04. 13Non-contacting Position Sensor Magnepot 6150 Environmental Operating Temperature Range -40C to +125C Shock Per MIL R-39023, 6 ms Saw-tooth 100 Gs Vibration Per MIL R-39023, 10 Gs, 100 to 500 Hz Moisture Resistance, Powered Per MIL 202G, Method 106G Rotational Life 50 million shaft revolutions with side load < 0.33 lb, 100 million with side load < 0.25 lb Storage Temperature Range -55C to +125C Ordering Information 6153 V1 A360 L.5 XX Model Series Optional Feature Code (see table) Voltage Output Code (see table) Electrical Angle (35 to 360 degrees, smaller angles are possible, consult factory) Linearity, Independent Feature Codes Voltage Output Codes Optional Feature Codes V0 3% to 96% FS Flatted Shaft V1 4% to 96% SS Slotted Shaft V2 5% to 95% LT Linearity Data V3 10% to 90% CW Reverse Direction V4 15% to 85% V5 20% to 80% When V0 is used the angle specified is the When multiple Optional Feature codes are theoretical angle over which the output used the P/N shall be in the same sequence would vary if the output could actually reach as listed in this table (top to bottom). 0% and 100% of Vcc. General Note TT electronics reserves the right to make changes in product specification without notice or liability. All information is subject to TT electronics own data and is considered accurate at time of going to print. www.bitechnologies.com TT electronics plc 04. 13