OVPL5W3K TT Electronics

OVPL5W3K Power Line Designer Kit 0.5-Watt LED Modules OVPL5W3K Contents: Five (5) PCBs 8 in length Product Photo Here Three (3) 0.5-Watt white LEDs per PCB, on-board regulator included Wire harness with connector Hand insertion tool The self-contained Power Line Designer Kit is a flexible and scalable lighting solution using mid-power LEDs to supply high luminous flux without additional heatsinking requirements. The kit includes components and instructions to allow a designer to configure LED placement as needed for uniform illumination in his application. With a 15-volt power supply (see Notes), the Power Line Kit is a total lighting solution. Applications PCB with 3LEDs Architectural accent lighting Viewing Typical Typical Luminous Optek Part No. Under-counter lighting Angle CCT Flux (lm) 15V* OPA773 Media illumination Lighting for large channel letters 50 1 board Backlighting for light boxes 100 2 boards Point-of-sale displays White 120 150 3 boards 5750K 200 4 boards 250 5 boards *125mA per board stabilized 8.75 by 1.5 tube 5 PCBs 8.00 x 0.425 wide (.062 FR4 material) 4 Wire harness with connector Notes: Hand Insertion Tool All electrical and optical characteristics of the LEDs remain the same as specified in Optek Datasheet OVS5WBCR4. Maximum storage and operating temperature 40 ~ +100C ESD threshold (HBM) 2000V RoHS DO NOT LOOK DIRECTLY 14-16V power supply not included. 1.0A minimum rating AT LED WITH UNSHIELDED EYES OR DAMAGE TO required, regulated or unregulated. RETINA MAY OCCUR. OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. OPTEK Technology Inc. 1645 Wallace Drive, Carrollton, Texas 75006 Issue A.3 06/08 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 visibleLED optekinc.com www.optekinc.com Page 1 of 2 OVPL5W3K OVPL5W3K Power Line Designer Kit OVPL5W3K OPA773 Dimensions 8.000 203.20 - BLACK WIRE 14-16 VOLT Remove adhesive backing DC INPUT Place in desired position OPA773 0.425 10.79 200mA min. per strip Attach 28-26 gauge wires with tool 9175 + RED WIRE 3.000 76.20 1.287 32.68 3.000 76.20 Suggested Design Options Number of LEDs per Number of Strips LED Drive Current Supply AWG Optek Part Number Strip per Buss per Strip Voltage 3 1 to 5 125mA 26-28 14-16V OPA773 (included in kit) 3 1 to 30 125mA 18 14-16V OPA775 3 2 to 60* 125mA 18 24V OPA776 Other Other Other Other Other Optek Custom Assembly** *Multiples of 2 only **Contact Optek or an authorized distributor to discuss your application. Instructions 1. Install backplane (not included) behind panel to be illuminated. 2. Use masking tape (not included) to temporarily position the boards on backplane. 3. Route wire harness to each strip: Start with loose end and work to- ward 2.1mm jack. Use insertion tool to insert red and black wires on each board. Leave several inches of slack be- tween each strip. 4. Connect the 2.1mm jack to 14-16V power supply (not included, must be rated at 1.0A minimum). 5. Reposition all boards until optimal illumination is achieved. 6. Peel tape backing from boards. 7. Permanently apply boards to backplane. Note: Steps 6 and 7 are optionaldo not peel off backing if the kit will be reused. Output connector 2.1mm ID/5.5mm OD OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. OPTEK Technology Inc. 1645 Wallace Drive, Carrollton, Texas 75006 Issue A.3 06/08 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 visibleLED optekinc.com www.optekinc.com Page 2 of 2 OVPL5W3K - BLACK 14-16VOLT Remove adhesive backing OPA773 DC INPUT Place in desired position + RED - BLACK 14-16 VOLT Remove adhesive backing OPA773 Place in desired position DC INPUT + RED - BLACK 14-16 VOLT Remove adhesive backing OPA773 DC INPUT Place in desired position + RED - BLACK 14-16VOLT Remove adhesive backing OPA773 DC INPUT Place in desired position + RED - BL- BLACACK K Remove adhesive backing 14-16 VOLT OPA773 DC INPUT Place in desired position + RE+ RED D WIRE